Publicidad
Idiomas disponibles
Idiomas disponibles
How to Operate the Remote Control Transmitter
TELEVISION Mode
0-9 Digit buttons
With the remote conirol transmitter you can
select channels by pressing the 0-9 digit but-
tons. First, select one digit or two digits using
the single/double entry —/-- button. Then
select the programme channel numbers (1 to
99).
Channel Selector (A/V)
See Section 3, 'Channel Selection' under
"Operation of Manual Controls."
Flashback &
Returns
tuning from the currently tuned
channel to the previously selected channel.
Example: Previously viewed channel: 4
Channel being watched:
10
While watching Pr 10, press the flashback
( ©) ) button to return to Pr 4. Press the but-
ton again to resume watching Pr 10.
Note:
This
feature
is effective
only
during
programme channel selection.
Sound Volume V 31 A
Press the A button to increase the volume,
and the V button to decrease it. The on-
screen
display is identical to the display
shown when the volume is adjusted on the
TV set.
ABEEROOIOIUDUD0
|
———— 7
Green
Red
Green
Sound Mute button
¢ When this button is pressed, the sound is
muted.
¢When this button is pressed once again,
the sound is restored.
On Screen Display
A symbol that looks like «{ appears in the
upper left corner of the screen.
Sound Tone Control ¢ /3' WOOFER
This set is equipped with three audio tone
control buttons {(
@: treble and
%*: bass
and
: woofer). Adjust them to your lik-
ing. The woofer buttons are effective only if
you connect the optional 'Super Woofer"' to
your TV set.
The same indication appears when the tre-
ble, bass, or woofer button are pressed.
Center (preset) position
ee a
SS
Red
Green
Balance
Ln1R
Press the balance control buttons to balance
the sound from the left and right speakers.
Center (preset) position
ase
|
a
Green
Red
Green
Sound normal button N
To reset the balance, treble, bass and woofer
back to their normal levels, press the normal
button.
If the sound normal button is pressed within
3 seconds of pressing the balance, treble,
bass or woofer buttons the above indication
appears. If pressed after 3 seconds, no indi-
cation appears.
Contrast
V @ A
Press the contrast button (A) to increase pic-
ture contrast. Press the (V) button to reduce
it.
Incorrectly adjusted
picture contrast
may
cause eyestrain.
Max {preset} position
tt
a
Pe
Red
Colour V @ A
Press the colour button (V) so the picture
changes to black and white, then press the
{A\) button to get the best "natural colour''
If you cannot obtain natural colour, readjust
the preset tuning control.
Brightness v Tt A
Press the brightness button (A) to increase
the brightness of the picture. Press the but-
ton () to reduce it. For best reception, ad-
a the picture brightness according to room
ight.
The
same
indication
appears
when
the
colour, or the brightness button is pressed.
Center (preset) position
|| | | | |
fs
hee
Red
Green
Picture normal button N
' For resetting the colour, contrast and bright-
ness back to their normal levels, press the
N(Normal) button.
If the picture normal button is pressed within
3 seconds of pressing the contrast, colour or
brightness button, the above indication ap-
pears. If pressed after 3 seconds, no indica-
tion appears.
Off-Timer button
The off-timer function switches the set auto-
matically into standby after a predetermined
period.
120, 90, 60 and 30-minute Off-Timer settings
are possible with this timer button. For exam-
ple, if the timer button is pressed for the first
time while receiving channel
programme
number 14, the 120-minute timer is set and
"© 120M Pri4/CH21" is displayed for ap-
proximately 3 seconds.
The second press sets the 90-minute timer
and ''@) 890M Pri4/CH21" is displayed.
The third press sets the 60-minute timer and
"@] 60M Pri4/CH21" is displayed.
The fourth press sets the 30-minute timer
and "@) 30M Pr14/CH21" is displayed.
When the timer button is pressed for the fifth
time, the timer is cancelled and nothing is
displayed on the screen.
Notes:
1. After the timer is set, the remaining time is
displayed on the screen at five minute in-
tervals. If you want to check the remaining
time, press the channel/timer call button.
Five seconds before going off, the screen
flashes "(]
OM Pri4/CH21" every other
second.
2. Ifthe OffTimer is reset, the timer memory
will be cancelled.
It is recommended that the set be switched
off manually using the main power on/off
switch, if it is to be left unattended for long
periods of time.
Channel Timer Call ©
eWhen
the channel/timer
call button
is
pressed when the Off-Timer is not set, the
channel programme number will be dis-
played in the upper right corner of the
screen.
¢The channel programme number display
can also be erased by pressing this button
again.
elf the Off-Timer had been set before the
channel/timer call button is pressed, then
the remaining time will be displayed in
minutes
to the
left of the
channel
programme number on the screen. For ex-
ample, "@) 23M Prt4/CH21" will be dis-
played 23 minutes before turn-off.
Note:
The On Screen
Display automatically ap-
pears for about 3 seconds under the following
conditions:
. Ceriain buttons on the TV or the remote
control transmitter are pressed.
. The TV receives stereo or bilingual televi-
sion signals.
. The
TV
receives
slow
switch
signals
through the 21-pin Euro-SCART.
TV/VIDEO Selector
When you press the TV/VIDEO selector, the
TV receives the Audio/Video signals through
the 21-pin AV terminal,
and
'AV'
(Au-
dio/Video
indicator) will be displayed
for
about 3 seconds in the upper corner of the
screen.
When
the TV/VIDEO
selector
is
pressed again, the set is switched to receive
on-air TV broadcasting,
and the channel
programme
number will be displayed for
about 3 seconds in the upper right corner of
the screen.
Publicidad
