Publicidad
Idiomas disponibles
Idiomas disponibles
Extending a Wire
When extending a wire, use a supplied coupler to connect the two wires.
1.
Insert the wires to the left and right of the three connection ports of the supplied coupler.
► Fig.21: 1. Coupler 2. Wire
NOTE: Insert both wires as far as they will go.
NOTE: Wire extension is possible by inserting into any two of the connection ports, but it is recommended to use the left and right connection
ports in order to extend in a straight manner.
2.
Clamp the coupler with pliers to fix the wires.
► Fig.22
Securing the charging station
Make sure that the cabtire cable can reach to the charging station and then secure it with screw pegs (8pcs) using the hex wrench 6.
► Fig.23: 1. Hex wrench 6 2. Screw peg (for fixing the charging station) (8 pcs)
Connecting the Wires to the Charging Station
When finished installing the wires, connect the boundary wire, guide wire, and cabtire cable to the charging station.
Connecting the boundary wire
1.
Open the terminal cover and remove the wire cover of the charging station.
► Fig.24: 1. Terminal cover 2. Wire cover
2.
Stand behind the charging station and pass the boundary wire coming from the left through the hook on the left side (3 hooks) from the bottom.
► Fig.25: 1. Boundary wire coming from the left side 2. Left-side hooks (three places)
3.
Insert the connector at the tip of the wire onto the terminal R.
► Fig.26: 1. Terminal R 2. Connector of boundary wire coming from the left side
NOTICE: To prevent the connector from being deformed or damaged, connect the connector straight without tilting it.
4.
Likewise, pass the boundary wire coming from the right side through the right-side hooks (three places) in order from the bottom and insert the
connector onto the terminal L.
► Fig.27: 1. Terminal L 2. Connector of boundary wire coming from the right side 3. Right-side hooks (three places)
NOTICE: Check that the boundary wires are connected to the proper terminals. If the boundary wires are connected to the wrong terminals,
the Robotic Mower will be unable to recognize the work area.
► Fig.28: 1. Boundary wire 2. Work area
Connecting the guide wire
Pass the guide wire through the right-side or left-side hooks (two places) and attach the connector at the tip of the wire to the terminal G1 or G2.
NOTICE: To prevent the connector from being deformed or damaged, connect the connector straight without tilting it.
NOTE: The guide wire connector can be attached to either terminal G1 or G2.
► Fig.29: 1. Guide wire connector 2. Terminal G2 3. Right-side hooks (two places) 4. Notch (Do not pass the guide wire through here)
NOTE: If there is a second guide wire, connect it to the open terminal G1 or G2 by the same procedure.
Connecting the cabtire cable
1.
Connect the cabtire cable connector to the socket.
► Fig.30: 1. Socket 2. Cabtire cable connector
NOTICE: To prevent the connector from being deformed or damaged, connect the connector straight without tilting it.
2.
Pass the cabtire cable through the center hooks (three places) in order from the top.
► Fig.31: 1. Center hooks (three places)
3.
Attach the wire cover.
•
Pass the cabtire cable through the notch in the wire cover.
► Fig.32: 1. Wire cover 2. Notch
4.
Close the terminal cover and connect the power plug of the AC adapter to a power outlet.
► Fig.33: 1. Terminal cover
5.
Check that the station indicator lights up green.
•
If the boundary wire is connected properly, the station indicator will light up green.
•
If there is a connection error, the station indicator will blink red. Remove any abnormalities in the charging station connection part or each wire,
and check the station indicator again.
► Fig.34: 1. Station indicator
27
ENGLISH
Publicidad
