Publicidad
Idiomas disponibles
Idiomas disponibles
OPERATION
IMPORTANT: Always follow safety precautions when operating this equip-
ment. Review the safety instructions.
not operate the system in the presence of any source of ignition including running or
hot engines, lighted tobacco products, gas or electric heaters, or any type of electronic
device. A spark can ignite fuel vapors.
OPERATION
IMPORTANT: Always follow safety precautions when operating this equip-
tight. If damaged, replace hoses before use.
ment. Review the safety instructions.
NOTE: Make sure the work area is dry.
not operate the system in the presence of any source of ignition including running or
NOTE: Ensure the tank contains enough fuel.
hot engines, lighted tobacco products, gas or electric heaters, or any type of electronic
device. A spark can ignite fuel vapors.
IMPORTANT: Make sure the fuel is not contaminated with debris. Tighten loose tank
lids regularly.
Dispensing Fuel
tight. If damaged, replace hoses before use.
Turn on the pump by removing the nozzle from the holder and pushing up the
do not run the pump more than 10 minutes with the nozzle closed. Leaving the pump
NOTE: Make sure the work area is dry.
switch lever. Insert the nozzle into the receiving tank and squeeze the handle
on with the nozzle closed for more than 10 minutes can damage the pump components
to start fuel flow. When done, release the nozzle handle, turn the pump off and
and will void the warranty.
return the nozzle to its holder.
NOTE: Ensure the tank contains enough fuel.
IMPORTANT: This pump is designed to be self-priming. If fuel is not delivered
within 15 to 20 seconds, turn the pump off and refer to priming information in the
IMPORTANT: Make sure the fuel is not contaminated with debris. Tighten loose tank
IMPORTANT: This is an intermittent duty pump, after running the pump for a
Troubleshooting Section.
lids regularly.
maximum of 30 minutes, allow it to cool for 30 minutes.
IMPORTANT: The motor is provided with an internal temperature-limiting device.
Excessive motor heat will trip the device and will only reset after the motor has cooled.
do not run the pump more than 10 minutes with the nozzle closed. Leaving the pump
If the device trips, turn the switch OFF and let the pump cool for 30 min. Turn the
on with the nozzle closed for more than 10 minutes can damage the pump components
switch ON again when ready to operate. If the device trips again before the end of the
and will void the warranty.
duty cycle, see the troubleshooting guide.
IMPORTANT: This is an intermittent duty pump, after running the pump for a
start pumping.
maximum of 30 minutes, allow it to cool for 30 minutes.
IMPORTANT: This is an intermittent duty pump, after running the pump for a
IMPORTANT: The motor is provided with an internal temperature-limiting device.
maximum of 15 minutes, allow it to cool for 30 minutes.
Excessive motor heat will trip the device and will only reset after the motor has cooled.
IMPORTANT: The motor is provided with an internal auxiliary timer circuit that limits
If the device trips, turn the switch OFF and let the pump cool for 30 min. Turn the
operation of the pump to the listed duty cycle. The timer circuit will turn th epump off
switch ON again when ready to operate. If the device trips again before the end of the
whn duty cycle is exceeded. After allowing the pump to cool for 30 minutes the pump
duty cycle, see the troubleshooting guide.
can be reset by turning the switch off and on.
start pumping.
IMPORTANT: This is an intermittent duty pump, after running the pump for a
maximum of 15 minutes, allow it to cool for 30 minutes.
IMPORTANT: The motor is provided with an internal auxiliary timer circuit that limits
operation of the pump to the listed duty cycle. The timer circuit will turn th epump off
whn duty cycle is exceeded. After allowing the pump to cool for 30 minutes the pump
can be reset by turning the switch off and on.
EN
To prevent physical injury or property damage, observe
precautions against fire or explosion when dispensing fuel. Do
Before each use, repair leaks around seals or connections.
Make sure hoses are in good condition and connections are
To prevent physical injury or property damage, observe
Make sure the pump is properly grounded. Repair any corroded
precautions against fire or explosion when dispensing fuel. Do
or damaged wiring before use.
Before each use, repair leaks around seals or connections.
Make sure hoses are in good condition and connections are
An automatic bypass valve prevents pressure build up when
the pump is on with the nozzle closed. To avoid pump damage,
Make sure the pump is properly grounded. Repair any corroded
or damaged wiring before use.
Never leave the pump running without fluid. Dry running can
damage the pump components, and will void the warranty.
An automatic bypass valve prevents pressure build up when
the pump is on with the nozzle closed. To avoid pump damage,
Never leave the pump running without fluid. Dry running can
Always turn the pump off if the temperature-limiting device
damage the pump components, and will void the warranty.
trips. If left on, the pump will automatically reset when cool and
Always turn the pump off if the temperature-limiting device
trips. If left on, the pump will automatically reset when cool and
1
2
3
1
2
4
5
3
6
4
7
5
8
6
9
7
10
8
11
9
12
10
11
12
11
Publicidad
