Publicidad
Idiomas disponibles
Idiomas disponibles
therefore subject to rules and restrictions regarding
transportation, storage, and recycling conditions.
ALPEN shall not be liable in the event of noncompli-
ance with these instructions.
HANDLING AND CHARGING
Do not use the battery if an evident visual defect can
be noticed.
When recharging, use only the compatible battery
charger sold with the original ALPEN equipment.
Do not leave the battery unattended while charging.
The battery must be charged in a dry ventilated room
where the temperature does not exceed the specified
values (4°C / 39°F and +45°C / 113°F).
Battery must be fully charged before storing it, after
the pruning season.
Outside of the pruning season, charge the battery
every three months, to avoid deep discharge.
Do not use batteries if you detect swelling and/or
unusual heat, smell, or discoloration of contacts, and
dispose the batteries at a local battery recycling center.
Do not immerse in water or expose to high humid-
ity rates.
Do not use or place near a source of heat or in strong
sunlight.
Do not expose to microwaves or high pressure.
Keep out of the reach of children.
Always keep batteries away from flammable materials!
INDICATION FOR USE AND STORAGE
CAUTION
When you first put your pruning shears WILDHORN
32 into service, please fully charge your batteries
before to use your pruning shears.
Before to store it at the end of the season, please
be sure to fully charge batteries. We recommend to
charge the battery every 3 month when you store it
for a longue period.
TECHNICAL SPECIFICATIONS
PRUNING SHEARS
Product
Cutting capacity
Weight of pruning shears
8
EN
5
(
)
ALPEN WILDHORN 32
Depending on the type
of wood, from 1 to 32mm
940g
BATTERY PACK SPECIFICATIONS
14.4V 2600MAH 37.44WH
Rated voltage
Number of cell
End charging voltage
End-of-discharge voltage
Max. charging current
Rated capacity
Charging temperature
range
The tool must be used only with ALPEN battery
TR-4S1P and ALPEN charger WEC-26WEAP-16800150AA.
Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs with
earthed (grounded).
USE
TURN ON AND TURN OFF THE TOOL
5
Insert the battery
(
)
into the pruning shears housing.
Once the battery has been fitted, press and hold
4
button
(
)
for about one second. A long acoustic signal
will be heard.
6
Press the trigger
(
)
quickly twice in succession. A
triple acoustic signal will be heard and the blade will
open.
At this point the machine is ready to be used.
To switch your pruning shears WILDHORN 32 off, close
1
the blade
(
)
by pressing the trigger
seconds until you hear the second double signal (hol-
ster mode), then release the trigger and press the
4
switch
(
)
for 1 second. You can also switch the pruning
shears off temporarily using the Holster mode (please
refer to the "Holster mode" paragraph).
SEMI-OPEN MODE
The user can set the blade to the semi-open mode at
any time. That can be useful while cutting branches
of small diameters.
To enable the semi-open mode, keep the trigger
pressed for 2 seconds until a double acoustic signal is
heard. Release the trigger to continue working.
To go back to the full opening mode, please follow the
same procedure.
PROGRESSIVE MODE
The pruning shears can be used in progressive mode
or in non-progressive mode. To switch from one mode
to the other, turn-off the tool, then hold the trigger
and press the ON/OFF button
long acoustic signal is heard.
14.4V
4
16.8V
10.8V
2A
37.44Wh
4-45°C
6
(
)
for about four
6
(
)
4
(
)
for 4 seconds until a
Publicidad
