Publicidad
Idiomas disponibles
Idiomas disponibles
1. Safety warnings common for
grinding, sanding, wire brushing,
polishing, carving or abrasive cut-
ting-off operations:
a. This power tool is intended to function
as a grinder, sander, wire brush, polisher,
carving or cut-off tool. Read all safety
warnings, instructions, illustrations and
specifications provided with this power
tool. Failure to follow all instructions list-
ed below may result in electric shock, fire
and/or serious injury.
b. Do not use accessories which are not spe-
cifically designed and recommended by
the tool manufacturer. Just because the
accessory can be attached to your power
tool, it does not assure safe operation.
c. The rated speed of the accessories must
be at least equal to the maximum speed
marked on the power tool. Accessories
running faster than their rated speed can
break and fly apart.
d. The outside diameter and the thickness of
your accessory must be within the capac-
ity rating of your power tool. Incorrectly
sized accessories cannot be adequately
guarded or controlled.
e. The arbor size of wheels, sanding drums
or any other accessory must properly fit
the spindle or collet of the power tool. Ac-
cessories that do not match the mounting
hardware of the power tool will run out of
balance, vibrate excessively and may cause
loss of control.
f. Mandrel
mounted
drums, cutters or other accessories must
be fully inserted into the collet or chuck.
If the mandrel is insufficiently held and/or
the overhang of the wheel is too long, the
mounted wheel may become loose and be
ejected at high velocity.
g. Do not use a damaged accessory. Before
each use inspect the accessory such as
abrasive wheels for chips and cracks,
sanding drum for cracks, tear or excess
wear, wire brush for loose or cracked
wires. If power tool or accessory is
dropped, inspect for damage or install
an undamaged accessory. After inspect-
ing and installing an accessory, position
4
1605A0014P 3100 202303.indd 4
Safety Rules for Rotary Tools
wheels,
sanding
SAVE THESE INSTRUCTIONS
yourself and bystanders away from the
plane of the rotating accessory and run
the power tool at maximum no-load speed
for one minute. Damaged accessories will
normally break apart during this test time.
h. Wear personal protective equipment. De-
pending on application, use face shield,
safety goggles or safety glasses. As ap-
propriate, wear dust mask, hearing pro-
tectors, gloves and workshop apron
capable of stopping small abrasive or
workpiece fragments. The eye protection
must be capable of stopping flying debris
generated by various operations. The dust
mask or respirator must be capable of fil-
trating particles generated by your opera-
tion. Prolonged exposure to high intensity
noise may cause hearing loss.
i. Keep bystanders a safe distance away
from work area. Anyone entering the
work area must wear personal protective
equipment. Fragments of workpiece or of
a broken accessory may fly away and cause
injury beyond immediate area of operation.
j. Hold the power tool by insulated gripping
surfaces only, when performing an op-
eration where the cutting accessory may
contact hidden wiring or its own cord.
Cutting accessory contacting a "live" wire
may make exposed metal parts of the pow-
er tool "live" and could give the operator
an electric shock.
k. Always hold the tool firmly in your
hand(s) during the start-up. The reaction
torque of the motor, as it accelerates to full
speed, can cause the tool to twist.
l. Use clamps to support workpiece when-
ever practical. Never hold a small work-
piece in one hand and the tool in the
other hand while in use. Clamping a small
workpiece allows you to use your hand(s)
to control the tool. Round material such as
dowel rods, pipes or tubing have a tenden-
cy to roll while being cut, and may cause
the bit to bind or jump toward you.
m. Position the cord clear of the spinning
accessory. If you lose control, the cord
may be cut or snagged and your hand or
arm may be pulled into the spinning ac-
cessory.
4/5/23 7:04 AM
Publicidad
