Kärcher CV 60/1 RS BP Manual De Instrucciones página 16

Error
2A
2B
2C
2E
32
33
35
80
81
82
8B
8C
8D
8E
8F
90
91
92
93
94
Description
HEPA filter bags (round)
Dust brush
Carpet brush
Hard floor brush
Crevice nozzle
Floor nozzle
Extension tube
Suction hose (3 m)
Key (2 x)
16
Cause
Brush motor DMC temperature error (FET)
Side brush motor DMC temperature error (FET)
Suction motor DMC temperature error (FET)
Lithium battery CAN communication error - Battery
CAN module not plugged in, installed upside down or
damaged.
Brush motor open circuit
Error in the brush motor high voltage protection
Error in the high-voltage protection of the drive motor 1. Ensure that the Grad is suitable for the device.
The battery is empty and must be recharged, transport
mode not possible
The filter bag is missing, transport mode still possible 1. Insert a filter bag.
The battery is empty and must be recharged, transport
mode still possible
The PWM of the drive motor is limited by an unspecified
source. All modes are still possible.
Drive motor reverse gear is limited. The reverse gear is
limited by a performance-limiting condition. All modes
are still possible.
Drive motor forward gear is limited. The forward gear is
limited by a power-limiting condition. All modes are still
possible.
Drive motor temperature is high. PWM limitation in the
range of high motor temperature. All modes are still
possible.
Drive motor ANIN Limit. The temperature of the motor
is above the software limit. The throttle entrance area
is impaired. All modes are still possible.
The PWM of the suction motor is limited by an unspec-
ified source. All modes are still possible.
The suction motor is limited by a power-limiting condi-
tion. All modes are still possible.
The battery is empty and needs to be recharged soon.
All modes are still possible.
The batteries are being charged and the device is
locked.
The PWM of the drive motor is limited by the active cur-
rent limit.
Rectification
1. Disconnect the power supply with the main switch.
2. Remove and clean the side brushes.
3. Remove the brush box and clean the brushes.
4. Allow the device to cool down for one hour before continuing operation.
1. Disconnect the power supply with the main switch.
2. Remove and clean the side brushes.
3. Remove the brush box and clean the brushes.
4. Allow the device to cool down for one hour before continuing operation.
1. Disconnect the power supply with the main switch.
2. Remove and clean the side brushes.
3. Remove the brush box and clean the brushes.
4. Allow the device to cool down for one hour before continuing operation.
1. Switch off the main switch and wait for 10 seconds.
2. Switch on the main switch.
1. Locate and reset the brush motor circuit breaker.
1. Locate and reset the brush motor circuit breaker.
2. Switch off the main switch and wait for 10 seconds.
3. Switch on the main switch.
1. Switch off the device.
2. Locate and lift the brake lever on the right side of the drive motor.
3. Charge the battery.
4. Make sure that the blue battery light in the left door is on during charg-
ing (only for lithium batteries).
5. If the battery light flashes or does not light up, press the button until it
lights up.
2. Make sure that the filter bag is properly fitted in the device.
1. Switch off the device.
2. Locate and lift the brake lever on the right side of the drive motor.
3. Charge the battery.
4. Make sure that the blue battery light in the left door is on during charg-
ing (only for lithium batteries).
5. If the battery light flashes or does not light up, press the button until it
lights up.
1. Ensure that the Grad is suitable.
1. Ensure that the Grad is suitable.
1. Ensure that the Grad is suitable.
1. Ensure that the Grad is suitable.
1. Ensure that the Grad is suitable.
1. Inform Customer Service.
1. Inform Customer Service.
1. Charge the battery as soon as possible.
1. Ensure that the key is switched off when charging.
1. Ensure that the Grad is suitable.
Accessories
Accessories
English
Part no.
8.634-529.0
6.903-887.0
8.634-882.0
8.634-884.0
6.903-403.0
6.907-410.0
8.600-009.0
8.645-088.0
8.600-486.0