Publicidad
Idiomas disponibles
Idiomas disponibles
GB
RANGER
4.1
INSTALLATION
4.1- Installed rearward-facing
Usage: ISOFIX+Support leg, Height: 40-105cm
Step1) Raise the seat slightly take out the support legs
support legs 90° perpendicular to the ground (see 3.8)
Step 2) If the vehicle is not equipped with ISOFIX guide sleeve (20), it needs to be installed as shown in the
figure
Step 3) Push ISOFIX on both sides of the base and clip it into the ISOFIX guide sleeve. When a
"click" is heard, the ISOFIX release button
Step 4) Press and hold the adjustment button on the support leg
until it contacts the vehicle ground, and the bottom of the support leg will be shown green;
Step 5) Turn the rotartion adjuster
(13)
to rotate the seat to the 90° hover direction, then place the child
on the safety seat, lock the buckle
(18)
and tighten the front tethe
Step 6) Turn the rotation adjuster (13). and adjust the 90 ° hover state to rearward-facing. The vehicle
can only drive after hearing the "click" sound.
*On the premise of not causing discomfort to children, tighten the shoulder belt as much as possible.
*The crotch strape should be as low as possible and should be located close to the crotch, not the abdomen.
*To ensure the comfort of your child, the safety belt must not be twisted
Pay attention!! Do not driving when the safety seat in the location of 90° hover.
4. 2- Installed forward-facing
Usage : ISOFIX+Support leg, Height: 76-105cm
A
Small Headrest +Cushion
B
Triangle sponge
Step 1) First, open the support leg to 90 ° (19);
Step 2) If the vehicle is not equipped with ISOFIX guide sleeve (20), it needs to be installed as shown
in the figure;
Step 3) Push ISOFIX on both sides of the base and clip it into the ISOFIX guide sleeve. When a "click" is heard,
the ISOFIX release button
(17)
is displayed in green color.
Step 4) Press and hold the adjustment button on the support leg
contacts the vehicle ground, and the bottom of the support leg will be shown green
Step 5) Put the child in the safety seat, and lock the buckle
Pls adjust the angle adjuster under the seat to choice a comfortable angle..
4. 3- Installed forward-facing
Usage 1: ISOFIX + 3 point belt, Height: 105-150cm
Step 1) Store the support leg
(19)
A
Press and hold the adjustment button on the support leg, and stow the support leg;
B
Then lift the seat and fold the support leg back into the seat bottom groove;
C
Finally, push the front protruding part inward
Step 2) If the vehicle is not equipped with ISOFIX guide sleeve (20),it needs to be installed as shown
in the figure;
Step 3) Push ISOFIX on both sides of the base and clip it into the ISOFIX guide sleeve. When a
"click" is heard, the ISOFIX release button
* See page 14, 3.6 "How to store the buckle and shoulder strap sleeve" to remove the parts.
Step 4)
(18)
Put the child into the safety seat, adjust the headrest up and down according to the height of child.
Step 5) Pull out the adult 3-point belt, D: Clip the vehicle shoulder belt into the belt guide hook of the headrest,
and then clip vehicle shoulder and lap belt together into the belt guide slot on the side of the seat, finally lock
the buckle..
Usage 2: only 3 point belt
Height: 105-150cm
22
(19)
rom the grooves of the base and then make the
(17)
is displayed in green color.
(19)
to adjust the length up and down
(14)
(19)
to adjust the length up and down until it
(8)
tighten the front tether (14).
(17)
is displayed in green color.
GB
RANGER
Step 1: Store the support leg
(19)
A
Press and hold the adjustment button on the support leg , and stow the support leg;
B
Then lift the seat and fold the support leg back into the seat bottom groove;
C
Finally, push the front protruding part inward;
Step 2) Put the child into the safety seat, adjust the headrest up and down according to the
height of child. (18). See page 14, 3.6 "How to store the buckle and shoulder strap sleeve" to remove the parts.
Step 3) Pull out the adult 3-point belt, D: Clip the vehicle shoulder belt into the belt guide hook of the
headrest, and then clip vehicle shoulder and lap belt together into the belt guide slot on the side of the seat,
finally lock the buckle.
* When using, it should be confirmed that the buckle of the adult 3-point belt does not interfere with the main
load-bearing contact point of the child restraint system. If in doubt, pls contact the manufacturer of the child
restraint system.
A
Small Headrest +Cushion
B
Shoulder sleeves / Shoulder straps
5.1
MAINTENANCE
Keep the metal parts clean and dry to prevent rusting. Regularly grease the mobile parts and mechanisms with
a silicone-based spray. Do not use oil or grease. Only use mild detergent and warm water to clean the plastic
parts. Do not expose the upholstery to sunlight for prolonged periods of time. The upholstery can be taken
off and washed.
P
30º C
5.2
Machine
Do not
Dryclean, any
Do not
wash, cold
bleach
solvent except
tumbel dry
trichloroethylene
5.3
DISASSEMBLY STEP
A_ Remove the button first. B_ Take off the cushion. C_ Take off the Triangle sponge
D_ Open both shoulder sleeves E_ Remove the cover on the headrest. F_ Finally, remove the cloth cover along
the edge of the seat.
6
THE MAIN TECHNICAL PARAMETERS
Distance from front to back of the seat:537mm
Distance form left to right of the seat:440mm
Height of the seat:572mm
Weight of the seat:11.5±0.5kg
INFORMATION ABOUT THE GUARANTEE
- This item is guaranteed against manufacturing defects as stipulated in the legal Directives and/or regulations
in force on guarantees for consumer goods applicable to the European Union and those of the country in which
it is marketed.
- It is essential to present the purchase invoice or receipt in order to process the guarantee through the seller
of the item or, failing that, through the manufacturer.
- The guarantee excludes anomalies or faults caused by misuse, non-compliance with the safety regulations
and instructions for use and maintenance provided, or due to wear and tear caused by normal use and regular
handling of the item.
- The label containing the serial number of your model must not be torn off under any cir-cumstances as it
contains information relevant to the guarantee.
C
Triangle sponge
D
Crotch pad
E
Buckle
Do not Iron
23
Publicidad
