Publicidad
Idiomas disponibles
Idiomas disponibles
Important Safety Information (Continued)
Be sure that the unit is operated only by persons who have read
u
and understand these instructions.
Be sure that the unit is placed or mounted on a flat level surface
u
prior to and during operation. The unit must not slide or shift
during operation.
Keep all persons away from the unit during operation.
u
NEVER allow children in the work area.
u
Do not allow persons wearing loose clothing or jewelry to start
u
or operate the unit. Loose clothing or jewelry may become
entangled in moving components, causing equipment damage
and or personal injury.
Keep all persons away from parts that move or become hot
u
during operation.
Use only unleaded fuel. Do not refill the fuel tank while the engine
u
is running. Use precautions to prevent fuel spillage during refills.
Be sure the fuel tank cap is securely in place before starting
the engine. Clean up any spilled fuel before starting the engine.
Allow engine to cool for at least two minutes before refueling.
Do not add fuel while smoking or if unit is near any sparks or
open flames. Do not overfill tank - allow room for fuel to expand.
Always keep nozzle in contact with tank during fueling. Never fuel
the unit indoors. Failure to follow these instructions could result in
death or serious injury.
To reduce fire hazard, keep engine / equipment exterior free of
u
oil, solvent, or excessive grease.
Never mix oil with gasoline for this engine.
This is a four cycle engine designed to run on
pure gasoline. Oil is used for engine lubrication purposes only.
All installation, maintenance, repair and operation of this
u
equipment should be performed by qualified persons only in
accordance with national, state, and local codes.
Verify that all components of the unit are clean and in good
u
condition prior to operation. Be sure that the insulation on all
cables, electrode holders, and power cords is not damaged.
Inspect compressed air system, fuel system and electrical
components for signs of damage, deterioration, weakness or
leakage. Always repair or replace damaged components before
operating the unit. Always keep panels, shields, etc. in place
when operating.
Check all fasteners at frequent intervals for proper tightness.
u
Always operate the unit in a clean, dry, well ventilated area. Do
u
not operate the unit in humid, wet, rainy, or poorly ventilated
areas.
Always shut the equipment off prior to moving the unit.
u
Do not use any part of the unit as a work surface.
u
Do not tamper with governor setting on engine. Overspeeding
u
the unit severely shortens engine life and may also be very
hazardous.
Shut off the engine and disconnect the spark
plug wire before performing any service or
maintenance to the unit.
GENERATOR SAFETY
Be sure all powered devices are shut off prior to connecting them
u
to the unit.
Be sure that all tools and appliances are in good repair and are
u
properly grounded. Use devices that have three prong power
cords. If an extension cord is used, be sure that it has three
prongs for proper grounding.
This unit may be used for emergency stand-by service. In such
u
cases, a manual transfer switch must be installed between the
electric utilities meter and the electrical distribution box. This
switch should be installed by a licensed electrician.
WELDER SAFETY
Always keep a fire extinguisher
accessible while performing arc
welding operations.
Improper use of electric arc
welders can cause electric shock,
injury, and death! Take all precautions described in this
manual to reduce the possibility of electric shock.
Always wear dry protective clothing and welding
u
gloves, and insulated footwear.
Be sure that the work piece is properly supported and grounded
u
prior to beginning any electric arc welding operation.
Coiled welding cable should be spread out before use to avoid
u
overheating and damage to insulation.
Never immerse the electrode or electrode
holder in water. If the unit becomes wet for
any reason, be absolutely certain that it is completely clean and dry
prior to attempting use!
Always attach the ground lead first.
u
Verify that the work piece is securely grounded.
u
Always shut off the unit when not in use and remove the
u
electrode from the holder.
Never allow any part of the body to touch the electrode and
u
ground or grounded work piece at the same time.
Awkward welding conditions and positions can be electrically
u
hazardous. When crouching, kneeling or at elevations, be sure
to insulate all conductive parts, wear appropriate protective
clothing, and take precautions to prevent injury from falls.
Never attempt to use this equipment at current settings or duty
u
cycles higher than those specified on the equipment labels.
Never use an electric arc welder to thaw frozen pipes.
u
Flying sparks and hot metal can
cause injury. As welds cool, slag
can be thrown off. Take all precautions described in this
manual to reduce the possibility of injury from flying
sparks and hot metal.
Wear ANSI compliant face shield or safety glasses with side
u
shield protection when chipping or grinding metal parts.
5
Publicidad
