Roborock S8 MaxV Ultra Manual Del Usuario página 8

A11-5—Drying Air Outlets
A11-6—Cleaning Tank of Edgewise
Mopping Module
A11-7—Dock Base
A11-8—Charging Contacts
A11-9—Robot Refill Port
A11-10—Dirty Water Tank
A11-11—Status Indicator Light
• Breathing: Emptying/Mop
washing
• Red: Dock error
• Dim: Charging/Drying
• Off: Powered off
Note: To minimize disturbance, the indicator light will
be off or dim in Do Not Disturb (DND) mode.
A11-12—Dust Container Cover
A11-13—Mop Washing Module
A11-13-1—High-Speed Maintenance Brush
A11-13-2—Washing Strip
A11-13-3—Water Outlets
A11-13-4—Maintenance Brush Latch
A11-14—Cleaning Solution Cartridge
A11-15—Dust Bag Slot
A11-16—Filter
A11-17—Dock Location Beacon
A11-18—Suction Inlet
A11-19—Water Filter
A12
Power Cord Storage
A12-1—Cord Storage Slot
A12-2—Power Port
A12-3—Cord Outlets
Note: Power cord can exit at either side.
Installation
B
B1
Important Information
B1-1— Tidy cords, hard or sharp objects
(such as nails and glass), and loose
items from the ground and move
any unstable, fragile, precious, or
dangerous items to prevent personal
injury or property damage due to
items becoming tangled in, struck
by, or knocked over by the robot.
B1-2— When using the robot in a raised
area, always use a physical security
barrier to prevent accidental falls
that may result in personal injury or
property damage.
Notes:
• When using the robot for the first time, follow it
throughout its whole cleaning route and watch for
potential problems. The robot will be able to clean by
itself in future uses.
• To prevent excessive buildup of dirt on the mop cloths,
floors should be vacuumed at least three times before
the first mopping cycle.
B2
Positioning the Dock
B2-1— Place the dock on a hard, flat floor
(wood/tile/concrete etc.), flat against
a wall, and remove the foam used to
secure the mop washing module in
shipment at the bottom.
B2-2— Attach the dock base by pressing
down both sides of the base firmly,
and then pressing the connecting part
08
in the middle until you hear a click.
B2-3— Connect the power cord to the back
of the dock, and keep the excess
cord inside the storage slot.
B2-4— Reserve a space of at least 0.82 m (2.7 ft)
in height, 0.42 m (1.4 ft) in width and
1 m (3.3 ft) in depth. Make sure that
the location has good WiFi access for a
better experience with the mobile app.
Plug in and make sure that the status
indicator light is on.
B2-4-1—More than 0.82 m (2.7 ft)
B2-4-2—More than 1 m (3.3 ft)
B2-4-3—More than 0.42 m (1.4 ft)
Notes:
• If the power cord hangs vertically to the ground, it
may be caught by the robot, causing the dock to be
moved or disconnected.
• The status indicator light is bright when the dock is
powered on, and dim during robot charging or mop
cloth drying.
• The status indicator light turns red if an error occurs.
• Place the dock on a hard, flat floor away from fire,
heat, and water. Avoid narrow spaces or locations
where the robot may be suspended in the air.
• Placing the dock on a soft surface (carpet/mat) may
cause the dock to tilt and cause docking and departing
problems.
• Keep the dock away from direct sunlight or anything
that may block the dock location beacon, otherwise
the robot may fail to return to the dock.
• Do not use the dock without the clean water tank,
dirty water tank, high-speed maintenance brush,
dust container cover, disposable dust bag, cleaning
tank of edgewise mopping module, cleaning solution
cartridge, or water filter.
• Maintain the dock according to the Routine Maintenance.
Do not clean the dock power cord and charging contacts
with a wet cloth or tissue.