Cebora CP-1611 Manual De Instrucciones página 9

SX
(wrench #13) by keeping fitting E (wrench #11) fastened.
• Replacing the welding torch body.
• Screw in fittings D and E accord-
ing to the arrow direction - Fig. 6.
• Tighten fittings, introduce the heat-
shrinking hose C and use a small
heat source to warm it up.
• Connect connector B, introduce
the welding torch body into the grip
seat and then connect connector A
by introducing it inside the grip as
shown in figure 4.
• Reposition LH grip making sure not
to flatten any wire between the grip
rims.
• Screw in the 6 screws V again.
5.3.2 Replacing the welding torch body CP161 MAR
• Remove clamp F1 Fig.7 and extract the sleeve;
Unscrew the retention dowel G and then handle M, pull it
back until all cables are shown (see Fig. 8).
• Disconnect connector A (push-button) and connector B
(pilot arc).
• Remove heat shrinking hose C and unscrew nut D
(wrench #13) by keeping fitting E (wrench #11) fastened.
• Replacing the welding torch body.
• Screw in fittings D and E according to the arrow direc-
tion - Fig .9.
• Tighten fittings, introduce the heat-shrinking hose C
and use a small heat source to warm it up. Make sure that
fittings are completely covered.
• Reconnect connectors A and B, screw in the handle M
and, then the retention dowel G.
Reposition the sleeve onto the handle and tighten the
fig. 3 clamp F1.
5.4
CP-161 MAR
• Unscrew the 6 screws V Fig.3 and remove the LH grip.
• With reference to Fig.4, lift the welding torch body with
cable and disconnect connector A (push-button) .
• Replace the grip with push-button, connect connector
A and introduce it inside the grip, as shown in figure 4,
and then position the welding torch body with cable
inside the RH grip seat.
• Fasten the LH side of the grip making sure not to flat-
ten any wire between the grip rims and then screw the 6
screws V again.
fig. 4
5.5
ADAPTER.
5.5.1 CP-161 MAR
• Unscrew the 6 screws V Fig.3 and remove the LH grip.
With reference to Fig.4, lift the welding torch body with
cable and disconnect connector A (push-button) and
connector B (pilot arc).
• Remove heat shrinking hose C and unscrew nut D
(wrench #13) by keeping fitting E (wrench #11) fastened.
• Replace the welding torch cable, manually screw fit-
fig. 5
tings D and E according to the arrow direction - Fig.6.
• Tighten fittings, introduce the heat-shrinking hose C
and use a small heat source to warm it up.
• Connect connector B, introduce the
body into the grip seat and then connect connector A by
introducing it inside the grip as shown in figure 4.
• Reposition LH grip making sure not to flatten any wire
between the grip rims.
• Screw in the 6 screws V again.
5.5.2 CP161 DAR
• Remove clamp F1 Fig.7 and extract the sleeve.
Unscrew the retention dowel G and then handle M, pull
it back until all cables are shown (see Fig. 8);
• Disconnect connector A (push-button) and connector B
(pilot arc).
fig. 6
• Remove heat shrinking hose C and unscrew nut D
(wrench #13) by keeping fitting E (wrench #11) fastened.
• Replacing the welding torch cable.
• Screw in fittings D and E according to the arrow direc-
tion - Fig.9.
• Tighten fittings, introduce the heat-shrinking hose C
and use a small heat source to warm it up. Make sure that
fittings are completely covered.
• Reconnect connectors A and B, screw in the handle M
and then the retention dowel G.
REPLACING THE GRIP WITH PUSH-BUTTON
REPLACING THE CABLE WITH CENTRAL
welding torch
9