cecotec DRUMFIT INDOOR 23000 KOSMOS PRO Manual De Instrucciones página 28

ENGLISH
1. PARTS AND COMPONENTS
Fig. 1.
1. Pedals
2. Locking bolt
3. Washers (Ф10)
4. Spring washers (Ф10)
5. Cap nuts
6. Control panel
7. Handlebar
8. Allen key (x2)
9. Flywheel
10. Handlebar support
11. Variable resistance/brake
12. Saddle
13. Saddle post
14. Height-adjusting knob for the saddle
15. Main frame
16. Crank
17. Spring
18. Mat
19. Front anti-roll bar
20. Rear anti-roll bar
21. Washer (Ф6)
22. Corrugated pipe
23. Screws M6*12
24. Trim
25. Spanner 13-15
26. Spanner 17-19
27. Wing nut
Note:
The graphics in this manual are schematic representations and may not exactly match the
product.
2. BEFORE USE
It is recommended that two people assemble assemble the device.
-
Take the product out of the box and remove all packaging materials.
-
54
DRUMFIT INDOOR 23000 KOSMOS PRO
Make sure all parts and components are included and in good conditions. Some components
-
are pre-assembled. Carefully check the pieces are not damaged. If they are, immediately
notify the Technical Support Service of Cecotec.
3. ASSEMBLY
Step 1. Stabilizer bars. Fig. 2
Take the stabilizer bars (19 and 20):
-
The stabilizer bar with wheels (19) will be placed on the front part with the bicycle body,
-
with the wheels facing outwards.
The stabilizer bar without wheels (20) will be placed in the rear part.
-
Place the main frame on the front stabilizer bar (19) by matching the holes with the
-
pre-assembled screws. Insert them on every hole and on the other side place a curve
washer (Ф10) (3), a spring washer (Ф10) (4) and a cap nut (5) on every screw. Tighten them
with the spanner 17-19 (26).
Repeat the previous process with the rear stabilizer bar (20).
-
Step 2. Pedals. Fig. 3
Pedals (1) are marked with L (left pedal) and R (right pedal).
-
Place the right pedal (1) on the right crank (12), in the bicycle direction, loosen the fixed
-
nut, insert the pedal on the crank, and tighten the nut again with both spanners (25 and
26) clockwise.
Place the left pedal (1) on the left crank (12), in the bicycle direction, loosen the fixed nut,
-
insert the pedal on the crank, and tighten the nut again with both spanners (25 and 26)
counterclockwise.
Step 3. Stem and handlebar
Remove the part placed inside the handlebar bracket, as it is used to protect this part
-
during transport, and insert the stem (10). Fig. 5
Place the handlebar (7) on the handlebar bracket (10) by matching the holes on both parts
-
and careful not to press the cables from both parts.
Place a washer (Ф6) (21) on every hole and insert a M6*12 screw (23) to join both parts. Use
-
the Allen key (8) to tighten them. Fig. 6
Place the cables inside the corrugated tube (22) to protect them. Fig. 9
-
Place the monitor (6). You must insert the batteries before installing it on the bicycle.
-
Connect the cables to the sensor (the cable from the bicycle body) and pulse connectors
-
(the cable from the handlebar). Fig. 8
Place the handlebar cover (24) by pressing it slightly. Fig. 7
-
ENGLISH
DRUMFIT INDOOR 23000 KOSMOS PRO
55