Publicidad
Idiomas disponibles
Idiomas disponibles
EN
Deactivating Pause
Once activated, the function can be deactivated by pressing the
pause button (6) again. The LED for the pause setting turns off and,
within 10 seconds, you must slide your finger along the cursor
below the illuminated area (from left to right). This allows the surface
to resume cooking and the timer starts from the same point at which
it was stopped.
Timer function
There are two versions of the timer function:
• An independent timer from 1 to 59 minutes: it beeps when
the time has run out. This function is always available and is
indicated by the clock symbol (24) which is located between
the - and + buttons (the symbol may be less bright if another
cooking area timer has a remaining time that is less than that set
on the independent timer).
• A timer from 1 to 59 minutes for each cooking area: it beeps
when the time has run out and turns off the cooking area where it
was set. The 4 cooking areas can be programmed independently
(the symbol may be less bright if another cooking area timer has
a remaining time that is less than that set on the independent
timer).
The type of timer activated is shown in the dedicated displays
(19-20-21-22). The timer with the least time is highlighted and the
related clock icon is brighter (13-24). The other timer settings are
still active and running, but the clock icon (13-24) will be less bright.
Another icon with the word "min" (23) appears when you set times
longer than 10 minutes. For example 0.1 1 indicates 0 hours and 1 1
minutes.
The separator dot (21) flashes when the timer is running, while the
dot is static while the timer is selected and thus modifiable.
Independent timer
• If the touch display is on, the independent timer can be used by
simultaneously pressing the + and - buttons. If all the cooking
areas are in position "0", this is the only timer available. The
clock icon (24) will turn on and the display will show "0.00".
If you do not select any button, the timer deactivates within 5
seconds.
• The time setting (0-1hour.59min) can be changed in increments
of one minute with the + button from 0 to 99.
• Holding down the + or - button dynamically increases the rate of
change up to a maximum value, without beeps.
• If the + (or -) button is released, the rate of increase (decrease)
starts again from the initial value.
• The timer can be set by either continuously pressing the + or -
buttons or by pressing successively (with beeps).
After the timer is set, it begins to count down. The expiry of the time
is signalled by a beep or by the flashing of the timer display, which
will show "00".
The beep will not stop until the + or - button is pressed. The display
stops flashing and turns off.
8
Turning off/changing the timer
• The timer can be changed or turned off at any time by turning on
the touch display again, if no cooking area is on, and pressing
the + and - buttons simultaneously to select the timer. At this
point, set it to "0" by pressing the - button, to turn it off, or by
pressing the + button to increase the time setting.
• The independent timer remains active even when the On/Off
button is pressed
Programming the timer for the cooking
areas
By turning on the touch display, you can program an independent
timer for each cooking area.
• At least one cooking area must be on and set to a certain level.
• By pressing the + and - buttons simultaneously, you can set a
countdown for turning off the cooking area. There are illuminated
clock icons (13) next to the display of the cooking area. To set the
timer on a cooking area when there are more than one cooking
area on, you must press the + and - buttons simultaneously. You
will note that the clock icon will light and move to the various
cooking areas each time you simultaneously press the + and -
buttons.
• When the timer of the cooking area is selected, the related
clock icon near the display becomes brighter (13). The timers
programmed for each cooking zone remain active.
• Other functions of the timer are the same as the independent
timer. To increase the time, use the plus button.
• The expiry of the time is signalled by a beep and "00" on the
display and the LED of the cooking area assigned to the timer
flashes. The cooking area is turned off and an "H" is shown if
the area is "hot", otherwise the display shows a hyphen. The
beeping and flashing of the display stop.
• Automatically after 2 minutes.
• When you press the + or - buttons, the timer display turns off.
Publicidad
