Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
INTERFACE COMPONENTS
• AXDIS-TY2 interface
• AXDIS-TY2 harnesses (LD-TYNOAMP, LD-BX-TY3 AND LD-2NAVAMP)
• Female 3.5mm connector with stripped leads
APPLICATIONS
TOYOTA
4Runner ..................................................2014-2019
Avalon .....................................................2015-2018
*Avalon ...................................................2013-2014
Camry ......................................................2014-2017
Camry (NAV) ...........................................2012- 2014
AxxessInterfaces.com
Toyota Interface with SWC
INTERFACE FEATURES
• Designed for both amplified and non-amplified models
• Provides accessory power (12-volt 10-amp)
• Retains audio controls on the steering wheel
• Provides NAV outputs (parking brake, reverse)
• Retains the factory AUX-IN jack
• Micro-B USB updatable
• Retains balance on amplified models
(non-amplifed models will retain balance and fade)
TOOLS REQUIRED
• Wire cutter • Crimp tool • Solder gun • Tape
• Connectors (example: butt-connectors, bell caps, etc.)
• Small flat-blade screwdriver
Corolla ......................................................2015-2018
Highlander ..............................................2014-2019
Prius/Prius V (NAV) ...............................2013-2016
RAV4 ........................................................2015-2018
Sequoia ....................................................2014-2019
Sequoia (w/NAV) ....................................2013
© COPYRIGHT 2024 METRA ELECTRONICS CORPORATION
2012-2019
Sienna ......................................................2015-2017
Tacoma ....................................................2014-2019
*Tundra ....................................................2014-2019
Venza .......................................................2014-2016
Venza (w/o separate screen) ...............2013
* Only for models with a JBL amplifier
AXDIS-TY2
I N S TA L L AT I O N I N S T R U C T I O N S
TABLE OF CONTENTS
Connections:
Non-Amplified Models: LD-TYNOAMP ...............2
Amplified Models: LD-BX-TY3 ............................3
3.5mm Jack SWC Retention ...............................4
Installing the AXDIS-TY2 .......................................4
Programming the AXDIS-TY2 ...........................4-5
Audio Level Adjustment .......................................5
Steering Wheel Control Settings
LED Feedback ......................................................5
Changing Radio Type..........................................6
Remapping the SWC Buttons ............................6
Dual Assignment Instructions ........................ 7-8
Troubleshooting.....................................................8
Visit
AxxessInterfaces.com
for more detailed information about
the product and up-to-date vehicle specific applications.
ATTENTION: With the key out of the ignition, disconnect
the negative battery terminal before installing this product.
Ensure that all installation connections, especially the air
bag indicator lights, are plugged in before reconnecting the
battery or cycling the ignition to test this product.
NOTE: Refer also to the instructions included with the
aftermarket accessory before installing this device.
REV. 4/23/24 INSTAXDIS-TY2
Publicidad
Manuales relacionados para Axxess AXDIS-TY2
Resumen de contenidos para Axxess AXDIS-TY2
- Página 1 Remapping the SWC Buttons ......6 • AXDIS-TY2 interface TOOLS REQUIRED Dual Assignment Instructions ......7-8 • AXDIS-TY2 harnesses (LD-TYNOAMP, LD-BX-TY3 AND LD-2NAVAMP) • Wire cutter • Crimp tool • Solder gun • Tape Troubleshooting.............8 • Female 3.5mm connector with stripped leads •...
- Página 2 CONNECTIONS: LD-TYNOAMP FOR NON-AMPLIFIED MODELS Red - Accessory Vehicle Connectors Orange/White - Not Used Blue/White - Not Used 16-Pin Blue/Pink - Not Used Light Green - Not Used Green - Not Used Green/Black - Not Used Green/Purple - Not Used LD-2NAVAMP Purple - Not Used Purple/Black - Not Used...
- Página 3 CONNECTIONS: LD-BX-TY3 FOR AMPLIFIED MODELS Red - Not Used Orange/White - Not Used Blue/White - Amp Turn On 16-Pin Blue/Pink - Not Used Vehicle Connectors Light Green - Not Used Green - Rear Left Speaker + Green/Black - Rear Left Speaker - Green/Purple - Not Used LD-2NAVAMP Purple - Rear Right Speaker +...
- Página 4 • For all other radios: Connect the 3.5mm jack from the AXDIS-TY2 harness into the jack on the 5. After a couple seconds the LED will turn on solid Red while the interface auto detects the aftermarket radio designated for an external steering wheel control interface.
- Página 5 Flash Count Radio Flash Count Radio 8. If the interface fails to function, refer to Resetting the AXDIS-TY2. Eclipse (type 1) † Note: The LED will turn on solid Green for a moment, and then turn off under normal Kenwood ‡...
- Página 6 1. Ensure the AXDIS-TY2 is visible so you can see the LED flashes to confirm button recognition. 5. Once the desired radio number has been selected, press and hold the Volume-Down button on the steering wheel until the LED goes solid.
- Página 7 The AXDIS-TY2 has the capability to assign (2) functions to a single button, except Volume-Up the AXDIS-TY2 that this function is not available and it will move on to the next function. and Volume-Down. Follow the steps below to program the button(s) to your liking.
- Página 8 2. Press and hold the reset button for two seconds, and then let go to reset the interface. Metra recommends MECP 3. Refer to “Programming the AXDIS-TY2” from this point. certified technicians AxxessInterfaces.com ©...
- Página 9 • Interfaz AXDIS-TY2 Remapeo de los botones SWC ......6 HERRAMIENTAS NECESARIAS • Arneses AXDIS-TY2 (LD-TYNOAMP, LD-BX-TY3 Y LD-2NAVAMP) Instrucciones de asignación dual ....7-8 • Cortador de cables • Pelacables • Pistola soldadora • Cinta • Conector hembra de 3.5 mm con conectores pelados Resolución de problemas ........8...
- Página 10 CONEXIONES: LD-TYNOAMP PARA MODELOS NO AMPLIFICADOS Red - Accessory Vehicle Connectors Orange/White - Not Used Blue/White - Not Used 16-Pin Blue/Pink - Not Used Light Green - Not Used Green - Not Used Green/Black - Not Used Green/Purple - Not Used LD-2NAVAMP Purple - Not Used Purple/Black - Not Used...
- Página 11 CONEXIONES: LD-BX-TY3 PARA MODELOS AMPLIFICADOS Red - Not Used Orange/White - Not Used Blue/White - Amp Turn On 16-Pin Blue/Pink - Not Used Vehicle Connectors Light Green - Not Used Green - Rear Left Speaker + Green/Black - Rear Left Speaker - Green/Purple - Not Used LD-2NAVAMP Purple - Rear Right Speaker +...
- Página 12 5. Después de unos segundos, la luz LED se encenderá en Rojo fijo mientras la interfaz detecta automáticamente el vehículo y los controles en el volante. Este proceso debe de tomar Para todos los demás tipos de radios: Conecte la entrada de 3.5 mm del arnés AXDIS-TY2 a la entrada •...
- Página 13 Retroalimentación LED Parpadeos Parpadeos 8. Si la interfaz no funciona, consulte la sección Restablecimiento de la interfaz AXDIS-TY2. Eclipse (tipo 1) † Nota: La luz LED se encenderá en Verde fijo por un momento. Después, se apagará en su Kenwood ‡...
- Página 14 1. Después de (3) segundos de girar la llave para encender la marcha, mantenga oprimido el 6. Pioneer/Jensen 14. Parrot botón de Bajar volumen en el volante hasta que la luz LED en el AXDIS-TY2 se encienda en 22.Axxera 7. Alpine 15.
- Página 15 (1) segundo hasta que se encienda la luz LED. Después, suelte el botón de Subir El AXDIS-TY2 tiene la capacidad de asignar (2) funciones a un único botón, salvo por los botones de Subir volumen. Esto le indicará ala interfaz AXDIS-TY2 que esta función no está disponible, por lo que volumen y Bajar volumen.
- Página 16 2. Mantenga oprimido el botón de reinicio durante dos segundos. Después, suéltelo para reiniciar la interfaz. Metra recomienda a los técnicos 3. Consulte la sección “Programación de la AXDIS-TY2” a partir de este punto. con certificación MECP AxxessInterfaces.com ©...