Publicidad
Idiomas disponibles
Idiomas disponibles
EN
–
Push the battery into the battery compartment until you hear the lock engage
V1.
Ensure that the lock moves freely and engages cleanly.
–
Close the battery cover. Ensure that the cover closes automatically. Dirt and
grass residue can prevent this and must therefore be removed.
Removing the battery (figure F + N2)
–
Switch off the motor F.
–
Open the battery cover and hold it open.
–
Press the release button on the motor unit (1) and remove the battery from the
battery compartment (2) N2.
–
Close the battery cover. Ensure that the cover closes automatically. Dirt and
grass residue can prevent this and must therefore be removed.
9 BEFORE INITIAL USE
Check all screw connections for a tight fit. Tighten the screws, if necessary. You
must check the fastening of the cutter bar in particular (see chapter "Maintenance
of the cutter bar").
The blade fastening screw must always be tightened by an authorised workshop. If
the blade screw is tightened excessively or insufficiently, blade fastening and cutter
bar may be damaged or get loose, which can lead to serious injuries.
The lawn mower is fitted with a motor stop device.
Before using the equipment for the first time, make sure that the motor stop safety
control bar is working perfectly. When the safety control bar is released, the cutter
bar must come to a standstill within 3 seconds.
After release, the safety control bar must always return to the position shown in the
"Description of components" diagram.
If this is not the case, it must be checked immediately by an authorised workshop.
Risk of injury!
If the stopping time of the blade is longer, stop using the device and take it to an
authorised workshop.
Measuring the stopping time
After starting the motor, the blade rotates and a wind noise can be heard.
The stopping time corresponds to the duration of the wind noise after the motor has
been stopped; it can be measured with a stopwatch.
Machine safety and protective devices must not be manipulated or disabled.
Make sure that all protective devices have been attached properly and are not
damaged.
Charging the battery (figure W2)
The handling of the charger and battery/batteries is
described
instructions. In particular, read and follow the safety
information! Charge the battery/batteries completely
before initial use! W2
All safety information concerning the handling, storage,
safekeeping, transportation and disposal of the lithium-ion
batteries, as well as first aid measures and measures for
extinguishing fires can be found in the "Product safety data sheet"
on www.sabo-online.com in the operating instructions area.
Information hotline for lithium-ion batteries
+49 (0) 2261 704-0
Battery level indicator (figure U4)
Press the battery level indicator button on the battery (1) to check the available
charge. The indicator LEDs (2) light up according to the level of charge of the
battery.
LEDs
Level of charge
and
indicator
5 green LEDs light up
4 green LEDs light up
Safety information!
For explanation of symbols, see the table on
in
the
relevant
separate
operating
Explanation
function
Battery is charged between
80% and 100%
Battery is charged between
60% and 80%
3 green LEDs light up
2 green LEDs light up
1 green LED lights up
1 red LED flashes
5 red LEDs flash
page 5
5 red LEDs light up
For BA1400T/BA2242/
BA2800T/BA4200T/
BA5600T/BA6720T:
5 red LEDs light up for
10 s, switch off for 10 s,
light up again for 10 s
or
5 green LEDs flash every
2 s
(depending
battery version).
For both displays, the
LEDs run through the
cycle continuously until
the self-maintenance is
complete.
For BA2240T:
No special indicator.
10 SWITCHING STANDBY MODE ON/OFF (FIGURE A2 + N2)
You must switch on standby mode in order to work with the mower.
Beforehand, please ensure that
–
there are one or two charged batteries in the battery compartment (see
chapter "Inserting the charged battery").
Switching on standby mode (figure A2)
–
Press the on/off button (1).
The LED on the motor unit lights up green.
–
To mow, start up the blade motor within 120 seconds of switching on standby
mode (see chapter "Starting the blade motor").
To protect the battery or batteries, standby mode is switched off
automatically if the blade motor is not started within 120 seconds.
The LED on the motor unit goes out.
If the LED lights up in another colour, this is a fault that must be rectified straight
away (see chapter "Fault indicator") or contact an authorised specialist workshop.
Switching off standby mode (figure A2)
–
Press the on/off button (1) again.
The LED on the motor unit goes out.
If you do not plan to use the device for a long time:
–
Remove the battery/batteries from the battery compartment N2.
11 CHANGING THE MOTOR SPEED (SWITCHING ENERGY-
SAVING MODE ON/OFF) (FIGURE F + H1)
The standard speed (TURBO) of the blade motor is 2800 revolutions per minute.
Adjustments to the motor speed can only be made when it is stopped.
To protect the battery and save energy, the speed can be lowered to 2400
revolutions per minute (ECO):
–
Switch off the motor F, wait until the cutter bar comes to a standstill.
10
Battery is charged between
40% and 60%
Battery is charged between
20% and 40%
Battery is charged between
10% and 20%
Battery has 10% charge or
less and must be charged
again soon
Battery is almost empty
and must be charged
immediately
irreparable damage (total
discharge)
Overheating
Allow the battery to cool to
below 67 °C
Self-maintenance
or
on
to
prevent
Publicidad
