Sabo 53-PRO E M VARIO Manual Del Operador página 52

EN
Grass is wet
In case of faults and defects which have not been listed here, please contact the
nearest authorised workshop.
Repairs which require specialised knowledge should only be performed by a
qualified expert. Your authorised workshop will naturally also be glad to help if you
do not wish to perform the maintenance work described here yourself.
21 MOTOR UNIT FAULT INDICATOR (FIGURE H (10))
Light signal Meaning
The motor unit is in good
Green LED lights
working order.
up
The motor unit has
Orange LED lights
overheated.
up
Battery pack is drained.
Red LED flashes
Blade motor overloaded.
Orange LED
flashes
Communication between
Red and green
battery and control board
LEDs flash
disrupted.
alternately
22 TECHNICAL DATA
Motor
Motor
Motor speed ECO
TURBO
Motor power ECO
TURBO
Charger
See the separate operating instructions for the charger.
Permitted temperature range during charging
Battery
See the separate operating instructions for the battery.
Recommended temperature range for storage
Mower
Housing
Cutting width
Cutting heights
Height-adjustable guide bar
Travel speed ECO
TURBO
Set a higher cutting height I.
Let lawn dry.
Fixing the fault
Not necessary.
Check and clean the air
filters W + W1.
Let the mower cool down.
Reduce the load and do not
use the motor unit when the
ambient temperature is high.
Let the mower cool down.
Charge the battery.
Clean grass from the cutting
space, remove blockages
(remove the
battery/batteries first N2 !).
Set a higher cutting height I.
When mowing on a slope:
reduce the travel speed or
switch off autodrive. Mow at
right angles to the slope, not
upwards.
Check that the battery is
positioned correctly, or that
the batteries are correctly
placed in the battery
compartment. Correct this if
necessary and restart the
motor.
Have it checked by an
authorised workshop.
56 V DC motor
2400 rpm
2800 rpm
1.7 kW
2.4 kW
+ 5 to + 40 °C
+ 10 to + 26 °C
Steel
530 mm
per axis, 7x
30, 40, 50, 62, 74, 85, 95
mm
3 possible settings
2.2 – 3.5 km//h
2.6 – 4.1 km/h
15
Weight Machine with empty collecting bag
Also with 2 x 56 V 12 Ah batteries
Length
Width
Height
Wheels front/rear
Bearing front
Bearing rear
Permitted temperature range during use
Permitted temperature range for storage
Maximum permitted humidity
Sound power level
Sound power level;
measured according to DIN EN IEC 62841-4-3
Measuring inaccuracies; according to DIN EN ISO 4871
Guaranteed sound power level;
measured according to 2000/14/EC
Sound pressure level
Emission sound pressure level at operator's workplace;
measured according to DIN EN IEC 62841-4-3
Measuring inaccuracies; according to DIN EN ISO 4871
Vibrations
The stated total vibration value has been measured according to a standardised
test procedure and can be used to compare the device with another machine. This
value can be used for a preliminary estimation of the vibration load.
Vibrations at the guide bar;
measured according to DIN EN IEC 62841-4-3
Measuring inaccuracies; according to DIN EN 12096
23 ORIGINAL SPARE PARTS AND ACCESSORIES
Recommended
lithium-ion batteries
All approved lithium-ion batteries are listed in the battery
Recommended
battery chargers
All approved chargers are listed in the battery operating
Filter
Roller bearing
grease
Cutter bar For safety reasons, the cutter bar must always be
replaced by an authorised workshop. This workshop has
the respective spare part number for the cutter bar
available.
46.0 kg
53.3 kg
1650 mm
575 mm
485 mm
Ø 210 mm / Ø 210 mm
Needle bearing
Bronze slide bearing
0 to + 45 °C
- 5 to + 60 °C
70 %, non-condensing
L = 90.1 dB(A)
WA
0.6 dB
L = 91 dB(A)
wa
L = 75 dB(A)
pA
3 dB
a = 0.90 m/s
2
hW
0.45 m/s
2
BA6720T (12 Ah, 672 Wh)
(Order no. SAB10424)
operating instructions
CH7000E (700 W)
(Order no. SAB10524)
instructions
SAE10418
SAA11300