Publicidad
Idiomas disponibles
Idiomas disponibles
ENGLISH
ENGLISH
Right Side
1.
Position the moulding with the bottom of the
moulding against the fence.
2.
Save the left side of the cut.
Outside Corner
Left Side
1.
Position the moulding with the bottom of the
moulding against the fence.
2.
Save the right side of the cut.
Right Side
1.
Position the moulding with top of the moulding
against the fence.
2.
Save the right side of the cut.
Cutting Crown Mouldings
The cutting of crown moulding is performed in a compound
mitre setting.
In order to achieve extreme accuracy, your saw has
pre-set angle positions at 31.6° mitre and there is also a
mark on the Bevel scale at 33.9° . These settings are for
standard crown mouldings with 52° angles at the top and
38° angles at the bottom.
♦ Make test cuts using scrap material before doing the
final cuts.
♦ All cuts are made in a left bevel and with the back of
the moulding against the base.
Inside Corner
Left Side
1.
Top of the moulding against the fence.
2.
Mitre right.
3.
Save the left side of the cut.
Right Side
1.
Bottom of the moulding against the fence.
2.
Mitre left.
3.
Save the left side of the cut.
Outside Corner
Left side
1.
Bottom of the moulding against the fence.
2.
Mitre left.
3.
Save the left side of the cut.
Right Side
1.
Top of the moulding against the fence.
2.
Mitre right.
3.
Save the right side of the cut.
SPECIAL CUTS
♦ All cuts are made with the material secured to the
table and against the fence. Be sure to properly secure
workpiece.
52
24
Bowed Material (Fig. 35, 36)
When cutting bowed material always position it as shown
in Figure 35 and never like that shown in Figure 36.
Positioning the material incorrectly will cause it to pinch
the blade near the completion of the cut.
Cutting Plastic Pipe or Other Round Material
Plastic pipe can be easily cut with your saw with the relative
blade applied. It should be clamped or held firmly to the
fence to keep it from rolling. This is extremely important
when making angle cuts.
Cutting Large Material
Occasionally a piece of wood will be too large to fit beneath
the blade guard. A little extra height can be gained by
rolling the guard up out of the way. Avoid doing this as
much as possible, but if need be, the saw will operate
properly and make the bigger cut. NEVER TIE, TAPE,
OR OTHERWISE HOLD THE GUARD OPEN WHEN
OPERATING THIS SAW.
Dust Extraction (Fig. 2, 3)
Fit the dustbag (ff) onto the dust spout (n).
WARNING: Whenever possible, connect a dust
extraction device designed in accordance with
the relevant regulations regarding dust emission.
Connect a dust collection device designed in
accordance with the relevant regulations. The air velocity
of externally connected systems shall be 20 m/s ±2 m/s.
Velocity to be measured in the connection tube at the point
of connection, with the tool connected but not running.
Transporting (Fig. 2, 6)
In order to conveniently carry the mitre saw, a carrying
handle (m) has been included on the top of the saw arm.
♦ To transport the saw, lower the head and depress the
lock down pin (o).
♦ Always use the carrying handle (m) or the hand
indentations (r) to transport the saw.
MAINTENANCE
Your STANLEY power tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper
tool care and regular cleaning.
♦ Regularly clean the ventilation slots in your tool using
a soft brush or dry cloth.
♦ Regularly clean the motor housing using a damp cloth.
Do not use any abrasive or solvent-based cleaner.This
machine is not user-serviceable. If problems occur
contact an authorised repair agent.
Lubrication
Keep "Lubrication" and "Cleaning" at the same
bottom line as the icon. The following text should
be started from the beginning of each row.
Cleaning
Before use, carefully check the upper blade guard,
movable lower blade guard as well as the dust
Publicidad
