Hallde RG-400 Instrucciones De Uso página 6

When removing, first remove the feed
attachment (1:A/1:B/1:C/1:D).
Lower the locking handle (2:F).
Remove the feed cylinder (2:A) from the
hinge pins (2:G) of the machine.
CHOOSING THE FEED ATTACHMENT
The feed hopper attachment (1:A) is used
mainly for cutting potatoes, onions, dry
bread, etc.
The tube attachment (1:B) is used mainly for
cutting cucumber, leek, paprika, etc.
The manual (1:C) and the pneumatic (1:D)
push feed attachments are used mainly for
cutting cabbage, lettuce, cheese, carrots,
etc.
FITTING AND REMOVING THE
FEED HOPPER ATTACHMENT (7:A)
Press in the stop button (2:C).
When fitting, fit the feed cylinder with two
internal guides (1:E).
Place the feed hopper attachment in the
centre of the feed cylinder, with the shaft
(7:B) in the feed cylinder tube (7:C).
Press down the feed hopper attachment and
turn the locking knob (7:D) anti-clockwise.
When removing, turn the locking knob (7:D)
clockwise and remove the feed hopper
attachment.
FITTING AND REMOVING THE
TUBE ATTACHMENT (8:A)
Press the stop button (2:C).
When fitting, fit the feed cylinder with three
internal knives (1:F).
Place the tube attachment in the feed
cylinder with the shaft (8:B) in the feed
cylinder tube (8:C).
Press down the tube attachment and turn
the locking knob (8:D) anti-clockwise.
When removing, turn the locking knob (8:D)
clockwise and remove the tube attachment.
FITTING AND REMOVING
THE MANUAL PUSH FEED
ATTACHMENT (9:A)
Press in the machine stop button (2:C).
For fitting, fit the feed cylinder with three
internal knives (1:F).
Move the lever (9:D) up all the way.
Fit the push feed attachment shaft (9:B) into
the feed cylinder tube (9:C).
Press down the push feed attachment and
swing it in anti-clockwise.
When removing, press down the stop pad
(9:E) and swing out the push feed
attachment clockwise and remove it.
FITTING AND REMOVING THE
PNEUMATIC PUSH FEED
ATTACHMENT (10:A)
Press in the machine stop button (2:C).
When fitting, fit the feed cylinder with three
internal knives (1:F).
Fit the push feed attachment shaft (10:B)
into the feed cylinder tube (10:C).
Press down the push feed attachment and
swing it anti-clockwise.
Push the compressor hose snap coupling
(10:D) onto the push feed attachment nipple
(10:E).
Set the speed controls of the machine (10:L)
and of the push feed attachment (10:M) to
suit the cutting tool being used as specified
in the instructions under the heading
SETTING THE SPEED CONTROLS.
Start the compressor and adjust its delivery
pressure to 6 bar, and handle the
compressor in accordance with the
manufacturer's instructions.
Check the air pressure on the pressure
gauge (10:F). The recommended air
pressure is about 4 bar, but the actual value
needed may vary. If the air pressure reading
on the pressure gauge is different, pull the
control (10:G) upwards and then turn it
until that the pressure gauge reading is
around 4 bar, and then press it back down
again.
When removing, switch off the compressor
and then disconnect the compressor hose
snap coupling (10:D) from the push feed
attachment nipple (10:E).
Press down the stop pad (10:H) and swing
out the push feed attachment clockwise,
and then remove it.
SETTING THE SPEED CONTROLS
The machine speed control (10:L) is
normally set to position "2" for all cutting
other than dicing, when the speed control
should be in position "1".
When cutting with the pneumatic push feed
attachment (10:A), set the speed control of
the machine (10:L) and push feed
attachment (10:M) in accordance with the
following table.
K/RT = Pneumatic push feed attachment.
M = Machine
Standard cutter 3 mm:
K/R-T= 2. M = 2.
Standard cutter 4.5-6 mm:
K/R-T= 3. M = 2.
Standard cutter 10-20 mm:
K/R-T= 3. M = 1.
Dicing cutter 12.5 mm:
K/R-T= 3. M = 1.
Julienne cutter 4.5 mm:
K/R-T= 3. M = 2.
Fine cut slicer 0.5-1.5 mm:
K/R-T= 1. M = 2.
Fine cut slicer 2-3 mm:
K/R-T= 2. M = 2.
Fine cut slicer 4-6 mm:
K/R-T= 3. M = 2.
Fine cut slicer 10 mm:
K/R-T= 3. M = 1.
Shredder 2.5x2.5 mm:
K/R-T= 2. M = 2.
Shredder 4.5x4.5-6x6 mm:
K/R-T= 3. M = 2.
Shredder 10x10 mm:
K/R-T= 3. M = 1.
Raw food grater 1.5 mm:
K/R-T= 1. M = 2.
Raw food grater 2-6 mm:
K/R-T= 2. M = 2.
Raw food grater 8 mm:
K/R-T= 3. M = 1.
Fine grater
K/R-T= 1. M = 2.
CLEANING
Switch off the machine and remove the
power supply plug from the socket or open
the isolating switch.
Carefully clean the machine immediately
after use.
Remove the feed hopper agitator (7:E) by
releasing the nut (7:F) by means of the
socket spanner (5:C).
Remove the two guides (1:K) and the three
knives (1:L) by releasing the nuts (1:M) by
means of the socket spanner (5:C).