Componentes Del Sistema; Diagrama De Conexión - DMP XR150 Serie Guia De Instalacion

COMPONENTES DEL SISTEMA

3.1 Diagrama de conexión
En el diagrama de conexión de la serie XR150/XR550 que aparece a continuación se muestran algunos de los módulos
accesorios que se pueden conectar para utilizar en diferentes aplicaciones. En la sección 3.3 se incluye una breve
descripción de cada módulo.
AC Wiring must be in conduit and exit out
the left side of the enclosure.
Wiring on terminals 5 through 22 must
exit right and maintain 1/4" separation
from the AC and battery positive wiring.
¼"
The plug-in transformer shall
plug into a 120 VAC 60 Hz
outlet not controlled by a
switch and all 16 to 18 gauge
wire shall run through conduit.
Bell
12 VDC
Minimum cuto time 5 min.
1.5 Amp Max
Digital Monitoring Products
4
Componentes del sistema
Power
LED
J3
Phone Line
XR550 Series
Panel
Outputs 3-6
Battery
Start
s
s
AC AC +B –B
BELL GND RED YEL GRN BLK
1 2 3 4 5 6 7 8
s
16 to 18 gauge wire
s
Maximum AC Wire distance
s
s
with 16 gauge wire: 70 feet
with 18 gauge wire: 40 feet
RED
BLACK
s s
Earth
Cold Water
Ground Ground
Pipe Earth
Ground
1k
Ohm
Bell
Bell cuto time
range is 5 to 99
minutes, non-coded.
Keyswitch Arming
can be connected
to any zone.
s s s s s s
s s s s s
Smoke
DISARM
Detector
ARM
1k Ohm 1k Ohm 1k Ohm
1k Ohm
Figura 1: Diagrama de conexión de la serie XR550
Form C Relays (J2)
Output Color Code–Model 431 Harness
Output 2 N/O Orange/White
Output 2 Com White/Gray
Output 2 N/C Violet/White
s
Output 1 N/O Orange
Output 1 Com Gray
Output 1 N/C Violet
Annunciator Outputs (J11)
Output Color Code
Output 3 Red
Output 4 Yellow
Output 5 Green
Output 6 Black
J11
Output 1 Output 2
J2
K6 K7
J13
J10
J4
Tamper
J8 J14 J9 J15 J17
PROG
SMK GND Z1 GND Z2 Z3 GND Z4 Z5 GND
9 10 11 12 13 14 15 16 17 18 19 20
S S S S S S S S S S S
1k 1k 1k 1k 1k
Ohm Ohm Ohm Ohm Ohm Ohm
Auxiliary/Smoke Power
Total current combined from terminals 7, 11,
25, 27, XBUS and LX500-LX900:
s s s
1.5 Amp Max 13.8 VDC to 10.2 VDC
BLACK
GREEN
YELLOW
RED
AUXILIARY/SMOKE POWER
RED
YELLOW
GREEN
BLACK
s
s
Zone Expander
Zone
Model 714
Expander
7 mA @ 12 VDC
Model 711
Models 714-8, 714-16
7 mA @
20mA @ 12 VDC
12 VDC
S S S S S S
1k Ohm 1k Ohm 1k Ohm
1k Ohm
Intended Installation Environment - Indoor/Dry
WARNING: Incorrect connections
may cause damage to the unit.
THIS UNIT MAY BE PROGRAMMED TO USE AN ALARM VERIFICATION FEATURE THAT
RESULTS IN DELAY OF THE SYSTEM ALARM SIGNAL FROM THE INDICATED CIRCUITS.
THE TOTAL DELAY (CONTROL UNIT PLUS SMOKE DETECTORS) SHALL NOT EXCEED 60
SECONDS. NO OTHER SMOKE DETECTOR SHALL BE CONNECTED TO THESE CIRCUITS
UNLESS APPROVED BY THE LOCAL AUTHORITY HAVING JURISDICTION (AHJ).
Front and Rear
s
tamper protection
s
included with Model
350 A Attack
Link LED Activity
Resistant Enclosure.
LED
s
J1
Ethernet
Tamper
Tamper
J18
Any other contact
J6
Load
devices listed for Fire
Protective Signaling
can be connected to
J16
zones
9 and 10.
Reset
J24
Zones 9 and 10 and
Cell Module
Model 715
compatibility
identifier: A
J19
Maximum operating
range: 13.8 VDC to
Class B (Style A).
Using verification
Z6 Z7 GND Z8 Z9+ Z9– Z10+ Z10–
delays on zones 9
and 10 is optional.
21 22 23 24 25 26 27 28
Use the delays
marked on the smoke
detectors.
Zone Zone
9 10
S S S S S
1k 1k 1k
Ohm Ohm
s
= Supervised Circuit
S S S S
3.3k 3.3k
Ohm Ohm
Resistor Resistor
Card
DMP DMP
Reader
Model Model
309 309
RED
Zone Expander
Model 715
7mA @ 12 VDC
Models 715-8, 715-16
20mA @ 12 VDC
Zone
Expander (up
to 8 zones)
Model 712-8
S S S S S
19 mA @
3.3k Ohm 3.3k Ohm 3.3k Ohm 3.3k Ohm
12 VDC
S S
S S
1k Ohm
Listed Resistors
1.0k Ohm - DMP Model 311
3.3k Ohm - DMP Model 309
10K Ohm - DMP Model 308
CAUTION: DO NOT USE LOOPED WIRE
UNDER TERMINALS. BREAK WIRE RUN TO
PROVIDE SUPERVISION OF CONNECTIONS.
WARNING
Guía de instalación de la serie XR150/XR550
Front
Rear
9.7 VDC.
S S S