Electric Fryers; Prolonged Disuse; Instructions For Cleaning; Reminders For Cleaning - Bartscher 650 SNACK Serie Instrucciones Para Instalación, Uso Y Mantenimiento

Off
Pilot ignition
1...6 Intermediate cooking temperatures
7 Maximum cooking temperature
BURNER IGNITION AND EXTINCTION
Pilot ignition
Press and turn the knob to position "
fully and light the pilot using the
• Hold the knob down for about 20 seconds before releasing it.
If the pilot fl ame goes out, repeat the operation.
• The pilot fl ame can be seen by opening the door
• The pilot light can be lit by bringing an open fl ame up to the
nozzle.
Main burner ignition
• Turn the knob to the chosen temperature setting for cooking.
Switching off
To switch the main burner off, turn the knob to position "
To switch off the pilot fl ame, press and turn the knob to position
" ".
12.2

ELECTRIC FRYERS

The thermostat control knob has the following positions:
0 Off
90 Minimum cooking temperature
120-150 Intermediate temperatures
180 Maximum cooking temperature
Switching on
• Turn the thermostat knob to the chosen temperature setting
for cooking.
• The yellow indicator light switches on.
• The yellow indicator light switches off when the oven reaches
the set temperature.
Switching off
• Turn the thermostat knob to position "0".
• The yellow indicator light switches off

13 PROLONGED DISUSE

Before any prolonged disuse of the appliance, proceed as fol-
lows:
• Clean the appliance thoroughly.
• Rub stainless steel surfaces with a cloth soaked in Vaseline
oil to create a protective fi lm.
• Leave lids open.
• Shut off taps and main switches upline of appliances.
Following prolonged disuse, proceed as follows:
• Inspect the appliance thoroughly before using it again.
• Allow electric appliances to operate at the lowest temperatu-
re for at least 60 minutes.

REMINDERS FOR CLEANING

The manufacturer will not be liable for any damage or in-
jury resulting from failure to observe the following rules
• Clean the satin fi nish stainless steel exterior surfaces, the
• At least twice a year, have an authorized technician clean the
• Do not use direct or high pressure water jets to clean the
". Press the knob down
• Do not use corrosive products to clean the fl oor beneath the
piezoelectric igniter.
• Clean with non-fl ammable detergents.
SATIN FINISH STAINLESS STEEL SURFACES
• Clean the surfaces with a cloth or sponge using water and
• Do not use pan scourers or other iron items.
• Do not use chemical products containing chlorine.
• Do not use sharp objects which might scratch and damage
".
COOKING WELLS
• Clean the wells by bringing the water to the boil, with the ad-
• Remove any limescale deposits with a proprietary limescale
14
The use of oil fi lters prolongs the life of the oil and, if the oil is
reused, guarantees better cooking of the food. To clean the
fi lter, extract it from its seat; if the fi lter is greasy, wash it with
a degreasing soap, rinse and dry When the procedure is con-
cluded refi t the fi lter in its seat When the fi lter is deteriorated it
must be renewed

REMINDERS FOR THE MAINTENANCE TECHNICIAN

The manufacturer will not be liable for any damage or in-
jury resulting from failure to observe the following rules
• Read this manual carefully. It provides important information
• Installation, conversion to a different type of gas and applian-
• Identify the specifi c appliance model. The model number is
• The appliance must be installed in a well-ventilated room.
• Do not obstruct any air vents or drains present on the ap-
• Do not tamper with appliance components.

15 CONVERSION TO A DIFFERENT TYPE OF GAS

See Chapter " Instructions for installation "

16 COMMISSIONING

Following installation, conversion to a different type of gas or
any maintenance operations, check appliance operation. In the
event of any malfunction, consult the next Paragraph "Trou-
bleshooting".

INSTRUCTIONS FOR CLEANING

cooking wells and the surface of the hotplates every day.
internal parts of the appliance.
appliance.
appliance.
proprietary non-abrasive detergents. Follow the direction of
the satin fi nish lines. Rinse repeatedly and dry thoroughly.
the surfaces.
dition of grease remover detergent if necessary
remover
FILTERS

INSTRUCTIONS FOR MAINTENANCE

for safe installation, use and maintenance of the appliance.
ce maintenance must be carried out by qualifi ed technicians
authorized by the manufacturer, in compliance with current
safety standards and the instructions in this manual.
detailed on the packing and on the appliance data plate.
pliance.
27