Symbols On The Machine - Metabo BAS 318 Precision WNB Manual De Instrucciones

en ENGLISH
Hazard generated by modification of
the machine or use of parts not tested and
approved by the equipment manufacturer!
 Assemble the machine in strict accordance with
these instructions.
 Use only parts approved by the manufacturer.
This applies especially to:
– Band saw blades (see "Technical
Specifications" for stock nos.);
– safety devices (see "Technical Specifications"
for stock nos.).
 Do not change any parts.
Caution!
The use of other tools and accessories can result
in a risk of injury.
Hazard generated by machine defects!
 Keep the machine and accessories in good
repair. Observe the maintenance instructions.
 Before every use check the machine for
possible damage: before operating the machine
all safety devices, protective guards or slightly
damaged parts need to be checked for proper
function as specified. Check to see that all
moving parts work properly and do not jam. All
parts must be correctly installed and meet all
conditions necessary for the proper operation of
the machine.
 Damaged protection devices or parts must be
repaired or replaced by a qualified specialist.
Have damaged switches replaced by a service
centre. Do not operate the machine if the switch
can not be turned ON or OFF.
 Keep handles free of oil and grease.
 Keep cutting tools clean and sharpened in able
to work better and safer.
 Do not used damaged or deformed band saw
blades.
Risk of injury by noise!
 Wear hearing protection.
Danger from blocking workpieces or
workpiece parts!
If blockage occurs:
1. switch machine off,
2. unplug mains cable,
3. wear gloves,
4. Clear the blockage using a suitable tool.

4.1 Symbols on the Machine

Danger!
Disregard of the following warnings may lead
to serious personal injury or material
damage.
Read instructions.
Wear protective goggles and ear
protectors.
Disconnect the mains plug before
starting any setting, maintenance or
repair work.
Do not direct the light beam into the
eyes of people or animals.
Wear ear protectors.
Belt width
Height adjustment
12
Operation of the quick release lever
Set belt tension.
Set angle of sawing table.
Set belt track.
Set cutting speed.
50Hz: 6,7m/s (400m/min) 50Hz: 13,3m/s (800m/min)
60Hz: 8,3m/s (500m/min) 60Hz: 16,7m/s (1000m/min)
Information on the nameplate:
(a)
Metabo- Allee 1, D-72622 Nuertingen,
Germany; Made in China
(b)
19009XXX
9997812345
(c) BAS 318 Precision WNB
1~ 220-240 V
50 Hz 410/880 m/min
60 Hz 490/1000 m/min
(d)
P 0,9 kW S1 100%
1
P 0,66 kW S1 100%
2
I = 4,0 A
(e)
(f) (g)
(a) Manufacturer
(b) Serial number
(c) Device designation
(d) Motor data (see also "Technical data")
(e) Disposal symbol – Device can be disposed of
via the manufacturer
(f) CE mark – This device fulfils the EU
Directives according to the Declaration of
Conformity
(g) Year of manufacture
(h) Dimensions of permitted saw belts
4.2Safety Devices
Upper blade guard
The upper blade guard (6) protects against
inadvertent contact with the saw belt and against
flying chips.
So that the upper saw belt cover provides sufficient
protection against contact with the saw belt, the
upper blade guide must be at least 3 mm from the
work piece.
Lower blade guard
The lower saw belt cover (8) protects against
inadvertent contact with the saw belt beneath the
sawing table.
The lower blade guard must be installed during
operation.
Housing doors
The housing doors (4) protect against contact with
the powered parts inside the saw.
The housing doors are equipped with interlocking
contacts. These turn the motor OFF when one
housing door is opened while the saw is running.
The housing doors must be closed while the
machine is in use.
Push stick
The push stick (10) serves as an extension to the
hand and protects against inadvertent contact with
the saw belt.
The push stick must always be used if the distance
between the saw belt and a rip fence is less than
120 mm.
The push stick must be held at angle of 20° ... 30°
to the surface of the saw table.
Replace push stick if damaged.
Hang push stick from the holder (12) when not in
use.
5. Overview
See page 2 - 3.
1 On/off switch cutting line illumination
2 On switch
3 Off switch
4 Housing doors
5 Turn-lock fastener for opening the housing
door
6 Upper saw belt guard (on the upper blade
guide)
7 Chips holder
8 Lower saw belt guard
9 Carry handles
10 Push stick
11 Allen key / tool storage for Allen key
12 Holder for storing the push stick
L=2240 mm
13 Hole in saw table
14 Saw table
max.
170 mm
15 Table insert
16 Chip extraction nozzle
17 Lower frame
18 Holder for storing the mitre fence
19 Transport rollers
6-20 mm
20 Height-adjustable lower frame foot
21 Clamping lever (angle adjustment for saw
(h)
table)
22 Saw table fastening screws
23 Setting knob (angle adjustment for saw table)
24 Rip fence screw on saw table
25 Fence guide extrusion
26 Parallel stop
27 Knurled nuts for fixing the profile rails
28 Profile rails of the parallel stop
29 Parallel stop clamping lever
30 Stop screws
31 Table widener / extension
32 Setting knob for saw belt tension
33 Display for saw belt tension
34 Quick release lever (for loosening the saw
belt)
35 Mitre fence
36 Clamping handle on the mitre fence
37 Setting knob (height adjustment for the upper
blade guide)
38 Lock nut (height adjustment for the upper
blade guide)
39 Upper blade guide
40 Setting knob for drive belt tension
41 Dust guard strip
42 Lock nut (for setting knob for the angle of the
upper band saw rollers)
43 Setting knob for the angle of the upper band
saw rollers
44 Upper thrust bearing
45 Screws for upper thrust bearing
46 Upper guide bearing
47 Screw for upper guide bearing
48 Lower thrust bearing
49 Screws for lower thrust bearing
50 Lower guide bearing
51 Screw for lower guide bearing
6. Unpacking, Erection,
Assembly and Transport
6.1 Unpacking
Unpack and transport saw with assistance from a
second person.
Do not lift or transport saw by holding the upper
saw belt guard (6).