EdilKamin LOGO Instalación Uso Y Mantenimiento página 26

DEVICES
he stove must O be installed in the same room as
e tractors, t pe heating appliances and other appliances
that ma affect its operation. See regulation
he stove is supplied with a power cable that is to be connected
to a socket, preferabl
mic switch.
oltage variations e ceeding
(unless alread installed, an appropriate differential switch
must be tted). he electrical s stem must compl with the
law; particularl verif the ef cienc of the earthing s stem.
he power line must have a suitable cross-section for the sto-
ve s power.
n inadequate earthing s stem can cause anomalies for which
Edilkamin cannot be held liable.
POSITIONING
he stove must be level for it to function correctl .
erif the bearing capacit of the oor.
FIRE PREVENTION SAFETY DISTANCES
he stove must be installed in compliance with the following
safet conditions
- medium ammabilit items must be kept at a minimum
distance of cm from the sides and back of the stove
- highl ammable items must be kept at a minimum
distance of 8 cm if placed in front of the stove.
f it is not possible to compl with the above mentioned
distances, technical and construction-related provisions
must be taken to prevent re ha ards. f connected to wooden
walls or other ammable materials, the smoke e haust pipe
must be appropriatel insulated
AIR INTAKE
he room where the stove is located must have an air intake
with cross section of at least 8 cm to ensurereplenishment
of the air consumed b combustion. lternativel , the stove
air ma be taken directl from outside through a cm steel
e tension of the pipe.
n this case,there ma be condensation problems and it is ne-
cessar to protect the air intake with a grille, which must have
a freesection of at least cm .
he pipe must be less than metre long and have no bends.
t must end with section at 9
with a wind guard. n an case all the wa air intake duct must
be a free section of at least
he e ternal terminal of the air inlet channel must be protected
with an anti-insect netting that does not reduce the
cm through passage.
INSTALLATION
8 .
tted with a magnetother-
% can damage the stove
facing downwards or be tted
cm .
SMOKE OUTLET
he smoke is discharged through the 8 cm diameter outlet at
the back of the stove.
he smoke outlet must be connected to outside b means of
suitable steel pipes E
ticall sealed.
he material used to seal and if necessar insulate the pipes,
must be resistant to high temperatures (high temperature silico-
ne or mastic).
he onl hori ontal section allowed ma be up to m long. t
ma have up to two 9
vertical section of at least . m and an anti-wind terminal
is necessar (if the discharge outlet is not in a chimne
reference 8 ).
he vertical duct can be internal or e ternal. f the smoke chan-
nel is outside, it must be appropriatel insulated.
f the smoke channel is tted inside a chimne
must be suitable for solid fuel. f it is wider than
diameter it must be improved b entering a pipe that has a
suitable cross-section and is made of suitable material (e.g. 8
mm diameter steel).
ll sections of the smoke duct must be accessible for inspec-
tion.
he chimne pots and smoke ducts connected to the solid fuel
appliances must be cleaned once a ear (verif whether a speci-
c legislation e ists in our countr ).
Failure to regularl inspect and clean the stove increases the
probabilit of a re occurring in the chimne pot. n that case,
proceed as follows o not use water to e tinguish the re;
Empt the pellet hopper; ontact specialist personnel before
reigniting the stove.
TYPICAL EXAMPLES
insulated steel ue
minimum height of . m and in an case above the height of the
roof gutter
air intake from inside room (minimum internal section 8 cm )
steel ue, inside e isting brick-built chimne .
CHIMNEY POT
he main characteristics are
- an internal cross-section at the base, which is the same as that
of the chimne ue
- an outlet cross-section which is no smaller than twice that of
the chimne ue
- its position must be high enough to catch the wind and avoid
downdraft areas in turbulent wind, it must be high enough to
catch the wind and avoid downdraft areas in turbulent wind.
- 26
-
8 certi ed. he pipe must be herme-
bends.
ue, the latter
-
ue -
mm in