Operation; Important - GBC Magnapunch 2.0 Manual De Instalación Y Funcionamiento

Magnapunch 2.0 – Installation and Operating Instructions
6. o
peRation
The Magnapunch 2.0 uses a variety of easily
interchangeable Die Sets for different binding styles.
By selecting the appropriate Die Set, you can use
your Magnapunch 2.0 to punch documents in any of
the binding styles indicated in the following table.
Table 1. Punch Styles
Binding Style
CombBind ®
Color Coil ®
Color Coil
Color Coil
WireBind ®
WireBind
VeloBind
SureBind ®
3, 5, or 7 Hole Binding 11 in. 3 holes across bound edge of document, 11 inch paper
2 or 4 Hole Binding A4
Note: Each punching style listed in the table requires
a separate Die Set for the Magnapunch 2.0. Custom
Die Sets for special punching patterns (not listed
above) can also be made to your specifications. For
more information on custom Die Sets, contact your
local GBC sales representative.
IMPORTANT: A decal on the handle of each
interchangeable Die Set indicates the punching
pattern for that Die Set. When reading the Operating
Instructions, please note the special instructions for
the correct punching pattern Die Set that you have
installed in your Magnapunch 2.0.
WARNING: Do not attempt to service or repair
the Magnapunch 2.0. Failure to observe this warning
could result severe personal injury or death.
Disconnect the plug from the receptacle and contact
your dealer or distributor, or GBC Technical Service
at one of the numbers below when one or more of
the following has occurred.
• The power supply cord or attachment plug is
damaged.
• Liquid has been spilled into the Magnapunch
2.0.
• The Magnapunch 2.0 is malfunctioning.
• The Magnapunch 2.0 does not operate as
described in these instructions.
Punch Pattern
Cerlox (Plastic Comb, Plastic Binding)
4:1 GBC (4 holes per inch 0.2475" center-to-center hole spacing)
4:1 Industry Standard (4 holes per inch, 0.2500" center-to-center
hole spacing)
5:1 (5 holes per inch)
2:1 (2 holes per inch) Both square and round hole patterns
available.
3:1 (3 holes per inch) Both square and round hole patterns
available.
1 hole per inch
Approximately 1 hole per inch
4 holes across bound edge of document, A4 paper
US - 800-723-4000
Canada - 800-463-2545
Mexico - (5525) 1500-5741
CAUTION:
• The receptacle must be located near
the Magnapunch 2.0 and must be easily
accessible.
• Disconnect the attachment plug from the
receptacle to which it is connected and keep
the power supply cord in your possession
while moving the Magnapunch 2.0.
• Do not use the Magnapunch 2.0 for other than
its intended purposes.
• Do not defeat or remove electrical and
mechanical safety equipment such as shields
and guards.
• Do not insert objects unsuitable for punching
or expose the equipment to liquids.
• Use only GBC Magnapunch 2.0
interchangeable Die Sets with the
Magnapunch 2.0.
Failure to observe these warnings could result in
severe bodily damage or death.
Minimum Margin
to First Binding
Hole
0.282 in. (7.2 mm)
0.092 in. (2.6 mm)
0.040 in. (1.0 mm)
1 0.030 in.
(0.8 mm)
0.375 in. (9.5 mm)
0.261 in. (6.6 mm)
0.500 in. (12.7 mm)
0.531 in. (13.5 mm)
Page 6-1