Intended Use; Ec Declaration Of Conformity; Instruction Manual - Makita DLS211 Manual De Instrucciones

WARNING:
Only use the battery cartridges and chargers listed above. Use of any other battery cartridges
DQG FKDUJHUV PD\ FDXVH LQMXU\ DQGRU ¿UH
Symbols
The following show the symbols used for the equip-
ment. Be sure that you understand their meaning before
use.
Read instruction manual.
7R DYRLG LQMXU\ IURP À\LQJ GHEULV NHHS
holding the saw head down, after making
cuts, until the blade has come to a com-
plete stop.
:KHQ SHUIRUPLQJ EHYHO FXW ¿UVW WXUQ WKH
1 2 3
knob counterclockwise and then tilt the
carriage. After that, turn the knob clockwise
to tighten.
:KHQ SHUIRUPLQJ VOLGH FXW ¿UVW SXOO FDU-
riage fully and press down handle, then
push carriage toward the guide fence.
Hold down the releasing button when tilting
the carriage to the right.
Engage the stopper lever when cutting a
base board in 45° miter angle.
'R QRW SODFH KDQG RU ¿QJHUV FORVH WR WKH
blade.
Never look into the laser beam. Direct laser
EHDP PD\ LQMXUH \RXU H\HV
Do not install the horizontal vise to the
same direction as the miter cutting. (This
V\PERO LV DSSOLHG RQ WKH KRUL]RQWDO YLVH
Only for EU countries
Ni-MH
Li-ion Do not dispose of electric equipment or
battery pack together with household
waste material! In observance of the
European Directives, on Waste Electric
and Electronic Equipment and Batteries
and Accumulators and Waste Batteries and
Accumulators and their implementation
in accordance with national laws, electric
equipment and batteries and battery
SDFN V WKDW KDYH UHDFKHG WKH HQG RI
their life must be collected separately and
returned to an environmentally compatible
recycling facility.

Intended use

The tool is intended for accurate straight and miter
cutting in wood. With appropriate saw blades, aluminum
can also be sawed.
Noise
The typical A-weighted noise level determined accord-
ing to EN62841-3-9:
Model DLS211
Sound pressure level (L
pA
Sound power level (L  G% $
WA
8QFHUWDLQW\ .  G% $
 G% $
Model DLS212
Sound pressure level (L
Sound power level (L
8QFHUWDLQW\ .  G% $
NOTE: 7KH GHFODUHG QRLVH HPLVVLRQ YDOXH V KDV EHHQ
measured in accordance with a standard test method
and may be used for comparing one tool with another.
NOTE: 7KH GHFODUHG QRLVH HPLVVLRQ YDOXH V PD\
also be used in a preliminary assessment of exposure.
WARNING:
WARNING:
use of the power tool can differ from the declared
value(s) depending on the ways in which the
tool is used especially what kind of workpiece is
processed.
WARNING:
sures to protect the operator that are based on an
estimation of exposure in the actual conditions of
use (taking account of all parts of the operating
cycle such as the times when the tool is switched
off and when it is running idle in addition to the
trigger time).
Vibration
7KH YLEUDWLRQ WRWDO YDOXH WULD[LDO YHFWRU VXP GHWHU-
mined according to EN62841-3-9:
Model DLS211
Vibration emission (a
8QFHUWDLQW\ .  PV
Model DLS212
Vibration emission (a
8QFHUWDLQW\ .  PV
NOTE: 7KH GHFODUHG YLEUDWLRQ WRWDO YDOXH V KDV EHHQ
measured in accordance with a standard test method
and may be used for comparing one tool with another.
NOTE: 7KH GHFODUHG YLEUDWLRQ WRWDO YDOXH V PD\ DOVR
be used in a preliminary assessment of exposure.
WARNING:
actual use of the power tool can differ from the
declared value(s) depending on the ways in which
the tool is used especially what kind of workpiece
is processed.
WARNING:
sures to protect the operator that are based on an
estimation of exposure in the actual conditions of
use (taking account of all parts of the operating
cycle such as the times when the tool is switched
off and when it is running idle in addition to the
trigger time).

EC Declaration of Conformity

For European countries only
The EC declaration of conformity is included as Annex A
to this instruction manual.
19 ENGLISH
 G% $
pA
 G% $
WA
Wear ear protection.
The noise emission during actual
Be sure to identify safety mea-
2
 PV or less
h
2
2
 PV or less
h
2
The vibration emission during
Be sure to identify safety mea-