Maintenance And Storage; Transport Position - Honda HF2315 Manual Del Operador

– Use counterweight(s) or wheel weights whenever advised in the
instructions manual.
13) Disengage the cutting means or the power socket when cross-
ing areas with no grass, when moving to or from areas that require
mowing, and move the cutting-means assembly to its highest posi-
tion.
14) Pay attention to traffic when using the machine near roads.
15) WARNING! The machine has not been approved for use on
public roads. It must be used (as indicated by the highway code) in
private areas closed to traffic.
16) Never operate the machine with damaged guards or without the
grass catcher, side discharge guards or discharge guards.
17) Never place your hands and feet near or under rotating parts.
Keep away from the discharge opening.
18) Do not leave the machine stationary on high grass with the en-
gine running to avoid the risk of starting a fire.
19) When using the attachments, never direct the opening towards
people.
20) Use manufacturer-recommended attachments only.
21) Don't use the machine if the attachments/tools are not installed
in their seats.
22) Pay attention when using the grass catcher and attachments
that can alter the stability of the machine, especially on slopes.
23) Do not change the engine settings or over-rev the engine.
24) Do not touch the engine parts as they get very hot when run-
ning. Danger of burns.
25) Disengage the cutting means or power socket, put in neutral
and engage the parking brake, turn off the engine and remove the
ignition key (checking that all moving parts are completely station-
ary):
– Whenever the machine is left unattended or the operator dis-
mounts from the driving seat:
– Before clearing blockages or unclogging the discharge chute;
– Before checking, cleaning or working on the machine;
– After striking a foreign object. Inspect the machine for damage
and make repairs before using it again.
26) Disengage the cutting means or the power socket and switch
off the engine (making sure that all moving parts are stationary):
– Before refuelling;
– Whenever you remove or reattach the grass catcher;
– Whenever you remove or reattach the discharge guard;
– Before adjusting the cutting height, if this operation cannot be
performed from the driving seat.
27) Disengage the cutting device or the power socket during trans-
port and whenever it is not in use.
28) Reduce the throttle setting before stopping the engine. Shut off
the fuel supply on completing the work, following the instructions
in the engine manual.
29) Pay attention to cutting means assemblies with more than one
cutting means, as a rotating cutting means can trigger the rotation
of the others,
30) WARNING – If something breaks or an accident occurs whilst
working, turn off the engine immediately and move the machine
away to prevent further damage; if an accident occurs with injuries
or third parties are injured, carry out the first aid measures most
suitable for the situation immediately and contact the medical au-
thorities for any necessary health care. Carefully remove any debris
that might cause damage or harm persons or animals should it not
be seen.
31) WARNING - The noise and vibration levels shown in these in-
structions are the maximum levels for use of the machine. The use
of an unbalanced cutting means, excessive speed of movement,
or lack of maintenance have a significant influence on noise emis-
sions and vibrations. Consequently, it is necessary to take preven-
tive steps to eliminate possible damage due to high levels of noise
and stress from vibration. Maintain the machine well, wear ear pro-
tection devices, and take breaks while working.
D) MAINTENANCE AND STORAGE
1) WARNING! - Before cleaning or doing maintenance work, take
out the ignition key and read the relevant instructions. Wear proper
clothing and protective gloves whenever your hands are at risk.
2) WARNING! – Never use the machine with worn or damaged
parts. Faulty or worn-out parts must always be replaced and not
repaired. Use original spare parts only: the use of non-original and/
or incorrectly fitted parts will jeopardize the safety of the machine,
may cause accidents or personal injuries for which the Manufac-
turer is under no circumstance liable or responsible.
3) Any adjustments or maintenance operations not described in this
manual must be carried out by your Dealer or a specialized Serv-
ice Centre with the necessary knowledge and equipment to ensure
that the work is done correctly maintaining the machine's original
safety level. Any operations performed in unauthorized centres or
by unqualified persons will totally invalidate the Warranty and all
obligations and responsibilities of the Manufacturer.
4) After each use, remove the ignition key and check for damage.
5) Keep all nuts, bolts and screws tight to be sure the equipment
is in safe working condition. Routine maintenance is essential for
safety and for maintaining a high performance level.
6) Check that the cutting means screws are properly tightened on
a regular basis.
7) Wear work gloves when handling, disassembling and reassem-
bling all cutting means.
8) Keep the cutting means well balanced during sharpening. All
works on the cutting means (disassembly, sharpening, balancing,
reassembly and/or replacing) are demanding jobs that require spe-
cial skills as well as special tools. For safety reasons, these jobs are
best carried out at a specialised centre.
9) Check that the brakes work properly on a regular basis. It is vital
for brakes to undergo regular maintenance and, where necessary,
repair work.
10) Check the side discharge guard, the discharge guard, the grass
catcher and the intake grille frequently. Replace them if they are
damaged.
11) Replace any instruction or warning message stickers, if dam-
aged.
12) When the machine is to be stored or left unattended, lower the
cutting-means assembly.
13) Store the machine out of the reach of children.
14) Do not store the machine with fuel in the tank in an area where
the fuel vapours could reach an open flame, a spark or a strong
heat source.
15) Allow the engine to cool down before storing in any enclosure.
16) To reduce fire hazards, keep the engine, silencer, battery com-
partment and petrol storage area free of grass, leaves, or excessive
grease. Always empty the grass catcher and do not leave contain-
ers full of cut grass inside storage areas.
17) To reduce fire hazards, check there are no oil and/or fuel leaks
on a regular basis.
18) If the fuel tank has to be emptied, this should be done outdoors
once the engine has cooled down.
19) Never leave the keys in the ignition or within reach of children
or unauthorised persons. Always remove the ignition key before
doing any maintenance.
E) TRANSPORT POSITION
1) WARNING! - If the machine must be transported on a truck or
trailer, use ramps with suitable resistance, width and length. Load
the machine with the engine switched off, without a driver and
pushed by an adequate number of people. During transport, close
the fuel stopcock (if fitted), lower the cutting-means assembly or
attachment, engage the parking brake and fasten the machine se-
curely with ropes or chains to the hauling device.
3 EN