Preparing Tea, Camomile, Etc; Adjustments And Settings Of The Dose; For Me Models; Technical Programming - Promac GREEN ME Manual Del Usuario

8.4. Preparing tea, camomile, etc.

● Place the jug under the hot water spout 4, Fig.3
and use the delivery control according to the mo-
del Fig. 8. When the desired quantity has been
obtained, close the tap (dispensing is automatically
halted according to the quantity set for models
GREEN ME).
During the delivery of hot water electronically dosed,
delivery can be interrupted by pressing button 6 Fig.
8.
To adjust the doses, see Paragraph 9.
● Add the desired product.
When purified water is used, these beverages often
assume a darker colour. Should the user prefer
a lighter coloured drink, draw fresh water from an
ordinary tap and proceed with the heating phase as
described in point 8.2.
9. ADJUSTING AND SETTING THE
DOSE
9.1. Models ME
The doses of coffee and hot water dispensed can be
adjusted on the electronically controlled models.
● Place the filter-holder with the ground coffee under
the unit to be programmed and the cup (or cups)
under the corresponding spouts;
● Keep the E key Fig. 8 of the keyboard located onto
the first group on the left hand side pressed for 5
seconds. The flashing leds of the E keys indicate
the enabling of the programming phase.
● Within 5 seconds press the appropriate key (A-
B-C-D) and visually check the delivery; when the
quantity delivered corresponds to the desired
amount, press the same key again; delivery cea-
ses and the volume of the dose is automatically
memorized.
● Carry out any other adjustment with the same
procedure which will also apply for hot water di-
spensing buttons (2 different doses) Fig.8.
Do not make adjustments to units that do not
have a filter-holder with coffee and correspon-
ding cups.
The adjustment made to the first unit on the left
also applies to the other units. If you wish to obtain
different doses from the other units, the unit on the
left must first be adjusted, followed step-by-step by
the others.
At the end of the programming phase wait at least 5
seconds before beginning the selections.
The data memorised is permanently stored within
the memory even in the case of complete absence
of electric power.
9.2 Technical programming (Mod.GREEN
ME)
The entrance in the TECHNICAL PRO-
GRAMMING environment enables the programming
of special parameters or functions.
To access TECHNICAL PROGRAMMING proceed
as follows:
- Turn off the machine
- Keep buttons A and E –group 1- pressed at the
same time
- Turn on the machine
- Wait (approx.3.seconds) for the machine to enter
programming
- Release the buttons
Some buttons belonging to the push button panel
of group 1 perform specific functions (other than
dispensing functions) when "TECHNICAL PRO-
GRAMMING" is under way.
A +
B -
C ENTER
E MENU'
 By accessing TECHNICAL PROGRAMMING in
the mode described above, the display will show
the first TECHNICAL parameter, i.e. the set LAN-
GUAGE.
If you want to modify the displayed parameter, act
on buttons A (+) B (-) to select the different options
available.
 To display the next parameter press E.
The USER NAME setting will be displayed.
If you want to modify the parameter (message) act
on buttons A (+) or B (-), to select the letters of the
alphabet; when the letter/symbol/number under the
flashing cursor is the desired one, press button C
(ENTER) to confirm the letter/symbol/number and
go to the selection of the next letter/symbol/num-
ber.
 To display the next parameter press E.
The setting of the continuous dispensing button
will be displayed.
If value 0000 is set, the button function will be to
STOP any dispensing.
If value 0001 is set, the button function will be to
START continuous dispensing.
To increment or decrement the numerical value,
press A (+) or B (-).
COVER
Function of "incrementing"
numerical values or selection of
"preset" options concerning the
parameter being programmed.
Function of "decrementing"
numerical values or selection of
"preset" options concerning the
parameter being programmed.
Function of confirming some
operations during program-
ming.
Function of selecting/choosing
the parameter to be program-
med.
73