baltur BTG 3,6 P Manual De Instrucciones página 25

WARNING NOTES FOR THE USER HOW TO
I
USE THE BURNER SAFELY
ELECTRICAL SUPPLY
• The equipment is electrically safe only when it is correctly connected
to an efficient ground connection carried out in accordance with
current safety regulations. It is necessary to check this essential
safety requirement. If in doubt, call for a careful electrical check by
a qualified technicians, since the manufacturer will not be liable for
any damage caused by a poor ground connection.
• Have qualified technicians check that the wiring is suitable for the
maximum power absorption of the equipment, as indicated in the
technical plate, making sure in particular that the diameter of cables
is sufficient for the equipment's power absorption.
• Adapters, multiple plugs and extension cables may not be used for
the equipment's power supply.
• An ominpolar switch in accordance with current safety regulations
is required for the mains supply connection.
• The electrical supply to the burner must have neutral to ground
connection. If the ionisation current has control with neutral not
to ground it is essential to make a connection between terminal 2
(neutral) and the ground for the RC circuit.
• The use of any components that use electricity means that certain
fundamental rules have to followed, including the following:
- do not touch the equipment with parts of the body that are wet or
damp or with damp feet
- do not pull on electrical cables
- do not leave the equipment exposed to atmospheric agents (such
as rain or sun etc.) unless there is express provision for this.
- do not allow the equipment to be used by children or inexpert
persons.
• The power supply cable for the equipment not must be replaced
by the user. If the cable gets damaged, switch off the equipment,
and call only on qualified technicians for its replacement.
• If you decide not to use the equipment for a while it is advisable
to switch off the electrical power supply to all components in the
system that use electricity (pumps, burner, etc.).
GAS, LIGHT OIL, OR OTHER FUEL SUPPLIES
General warning notes
• Installation of the burner must be carried out by qualified
technicians and in compliance with current law and regulations,
since incorrect installation may cause damage to person, animals
or things, for which damage the manufacturer shall not can be held
responsible.
• Before installation it is advisable to carry out careful internal
cleaning of all tubing for the fuel feed system to remove any
residues that could jeopardise the proper working of the burner.
• For first start up of the equipment have qualified technicians carry
out the following checks:
• If you decide not to use the burner for a while, close the tap or
taps that supply the fuel.
Special warning notes when using gas
• Have qualified technicians check the following:
a) that the feed line and the train comply with current law and
regulations.
b) that all the gas connections are properly sealed.
• Do not use the gas pipes to ground electrical equipment.
• Do not leave the equipment on when it is not in use and always
close the gas tap.
• If the user of is away for some time, close the main gas feed tap
to the burner.
• If you smell gas:
a) do use any electrical switches, the telephone or any other object
that could produce a spark;
b) immediately open doors and windows to create a current of air
that will purify the room;
c) close the gas taps;
d) ask for the help of qualified technicians.
• Do not block ventilation openings in the room where there is gas
equipment or dangerous situations may arise with the build up of
toxic and explosive mixtures.
FLUES FOR HIGH EFFICIENCY BOILERS AND SIMILAR
It should be pointed out that high efficiency boilers and similar
discharge combustion products (fumes) at relatively low temperatures
into the flue. In the above situation, traditional flues (in terms of their
diameter and heat insulation) may be suitable because the significant
cooling of the combustion products in these permits temperatures
to fall even below the condensation point. In a flue that works with
condensation there is soot at the point the exhaust reaches the
atmosphere when burning light oil or heavy oil or the presence
of condensate water along the flue itself when gas is being burnt
(methane, LPG, etc.). Flues connected to high efficiency boilers and
similar must therefore be of a size (section and heat insulation) for
the specific use to avoid such problems as those described above.
3 / 20
0006080763_201008
E
N
G
L
I
S
H