Oil Change; Air Filter Maintenance; Important - Stiga WBE120 Manual De Instrucciones

By pushing the button (fig. 7.E) the lights showing
the battery's residual charge will light up:
• three green lights and one red mean that
the charge ranges from 100% to 78%
• two green lights and one red mean that
the charge ranges from 77% to 55%
• one green light and one red mean that
the charge ranges from 54% to 33%
• a red light means that the residual
charge ranges from 32% to 10%.
• a blinking red light means that the charge
is lower than 10% and that the battery
should be recharged as soon as possible.
5.3.3 Refitting the battery on the machine
When recharging is completed:
1. disconnect the battery from
the battery charger
2. Disconnect the battery charger (fig.
7C) from the mains power supply;
3. insert the battery (fig. 1.G
by pushing it downwards (fig. 6.B) until
you hear a "click": this sound means
that the battery is locked in its position
and that the connection is ensured;

5.4 OIL CHANGE

For the required type of oil, observe the indications
provided in the technical data table.

IMPORTANT

gine is warm, being careful not to touch the hot en-
gine nor the drained oil.
See the specific chapter for the oil to be used.
IMPORTANT
gine is warm, being careful not to touch the hot en-
gine nor the drained oil.
a) Place engine level.
b) Make sure that the fuel tank is not full and that the
cap is properly closed.
c) Clean around oil fill (fig. 2.A.).
d) Remove the filler cap (fig. 2.A).
e) Have a container ready (fig. 8.B) to collect the oil.
f) Tip the lawnmower on its right side so that the oil
will drain from the oil fill (fig. 8).
g) Place the lawnmower level and top up with new
oil (see 4.1.1).
h) Check that the oil level has reached the «MAX»
notch on the dipstick (fig. 2.B).
j) Close the filler cap and wipe off any spilled oil.
in its housing
)
Drain the oil out while the en-
Drain the oil out while the en-
5.5 CLEANING THE SILENCER
AND THE ENGINE
The silencer must be cleaned when the engine is
cold.
a) Use a jet of compressed air or a brush to remove
any debris and dirt that could cause a fire from
the silencer (fig. 9.A) and its protective cover (fig.
9.B).
b) Clean the cylinder and cylinder head fins (fig. 9.C)
to ease engine cooling and prevent overheating.
c) Clean the plastic components with a sponge (fig.
9.D) soaked in water and detergent.

5.6 AIR FILTER MAINTENANCE

The filtering element must be kept perfectly clean and
must be replaced if it is broken or damaged.
a) Clean around the filter cover (fig. 4.A).
b) Remove the cover (fig. 4.A) by releasing the tabs
(fig. 4.B).
c) Remove the filtering element (fig. 4.C or 4.C.1).
d) Block the inlet duct (fig. 4.E) with a rag to prevent
any dirt from entering.
e) Carry out maintenance on the filtering element as
described below for each type.
f) Clean inside the filter housing (fig. 4.D) to get rid
of any dust, debris or dirt, taking care not to push
anything into the induction pipe (fig. 4.E).
g) Place the filtering element (fig. 4.C or 4.C.1) into
its housing and close the cover (fig . 4.B).
• Sponge filtering element (fig. 4.C)
Keep the filtering element clean and soaked in oil.
Replace it if it is disintegrating, cut or broken.
IMPORTANT
clean the filtering element.
– Clean the sponge filtering element with water and
detergent and dry it with a clean cloth.
– Soak the filtering element in 2 tablespoonfuls of
clean engine oil and wring it well to distribute the
oil evenly.
– Remove any excess oil with a clean cloth.
If you need to replace the filtering element, oil the
new filter as described above.
• Cartridge filtering element (fig. 4.C.1)
– Blow compressed air from the inside to remove
dust and debris.
8
Do not use compressed air to