Programming - Comunello Automation QUAD - 24V - HP Instrucciones De Uso Y De Instalacion

OPERATION WITH TIMER:
The control unit allows a timer to be connect in place of the open – close
pushbutton.
E.g.: at 08.00 am the timer closes the contact and the control unit
commands an opening movement; at 06.00 pm the timer opens the
contact and the control unit commands a closing movement. From 08.00
am – 06.00 pm at the end of the opening cycle the control unit disables the
flashing light, automatic closing and the remotes.
ELECTRIC LOCK CONTROL OUTPUT:
The control unit features an output to control a 12Vdc 15W max electric
lock. The command is switched on at each initial opening movement for a
period of 2 seconds.
SW2 SW2
BACK-UP BATTERY:
ON ON
The control unit has an integrated 13.7 Vdc battery charger (so also for 24V
Operators a 12V battery must be fitted). The control unit allows connection
of a back-up battery with maximum capacity of 7Ah, which will allow the
execution of several complete opening and closing cycles at reduced
1 2 1 2
speed in emergency mode. If fitted, a Flashing Light will operate only for the
INV INV INV INV
first 4 seconds of the movement when mains power is absent.
OFF OFF MOT 1 OFF
DIRECTION OF RUN CONTROL IN OPERATOR
1 AND OPERATOR 2
SW1 SW1
ON ON
1 2 1 2
1 NOT 2 MOTOR
MOTOR CONSID. MOTORS 2 DELAY
Important Note: Warning: change the settings of dip-switches SW1 and
SW2 with the control unit off and only subsequently repeat the control unit
programming procedure.
The electronic control unit is equipped with a SW2 dip-switch that can be
used to change the direction of run of each connected operator without
rewiring the electrical connections: dip-switch 1 of WS2 controls operator
1 while dip-switch 2 of SW2 controls operator 2.
M1 OR M2 DELAY CONTROL AND ENABLING
OF 1 OR 2 MOTORS
SW2 SW2
ON ON
1 2 1 2
INV INV INV INV
OFF OFF MOT 1 OFF
The electronic control unit is equipped with a SW1 dip-switch that is used
to select operation with 1 or 2 operators and to define which of the two
starts first and which starts second.

PROGRAMMING:

SELECT key: selects the type of function to store; the selection is indicated
by blinking of the LED.
Press the key twice to go to the required function. The selection remains
active for 10 seconds shown by blinking of the LED; when this interval
elapses the control unit returns to the original state.
SW1 SW1
ON ON
SW2 SW2
ON ON
1 2 1 2
INV INV INV INV
OFF MOT 2 MOT 1 MOT 2
SW1
ON
1 2
2 MOTOR
MOTORS 1 DELAY
SW2 SW2
ON ON
1 2 1 2
INV INV INV INV
OFF MOT 2 MOT 1 MOT 2
SW1
ON
SET key: programs the information in accordance with the function type
preselected with the SEL key. IMPORTANT: The SET key function can be
replaced by the remote if programmed beforehand (CODE LED on).
Programming enabled only when safety devices are not active.
MAIN MENU
The control unit is factory set to allow the selection of several important
functions.
L1 STEP-BY-STEP Step-by-Step
L2 CODE TX Code entered
L3 CONDO
L4 MOTOR TIME Programmed time
L5 PAUSE TIME With automatic closure
L6 DELAY
L7 AUTOM PRG
LEV MENU
1. STEP-BY-STEP:
n the default configuration the control unit is set with "Automatic" operating
logic enabled (LED n1 off); if the "Step-by-Step" operating logic is required
(LED n1 on), proceed as follows; use the SELECT key to select blinking
LED n1 and then press the SET key: LED n1 becomes steady on and
programming will be completed.
If the "Step-by-Step 1" operating logic is required, repeat the operation
above described, by pressing the SEL key twice instead only one (to obtain
the quick blinking of LED. Repeat the procedure if you wish to restore the
previous configuration.
2. TX CODE: (Radio control code):
Up to 120 remotes with different codes of either the fixed or rolling code
type can be saved on the control unit.
Programming:
Programming of the transmission code is performed as follows: use the
SELECT key to select blinking LED L2. Press SET once; the LED will
change its blinking mode (longer 1 0 1 0) to show that the
first level is being saved. On sending the selected code with the required
remote, the CODE LED will remain steady on to indicate that programming
has been completed.
To save the code for pedestrian opening / single leaf proceed as follows:
use the SELECT key to select blinking CODE LED L2. Press SET twice
consecutively; the LED will change its blinking mode (1 1 0 1 1 0) to show
that
the pedestrian code is being saved. On sending the selected code with the
required remote, the CODE LED L2 will remain steady on to indicate that
programming will be completed.
To save the code for the 2nd AUX channel proceed as follows: use the
SEL key to select blinking LED L2. Press SET three times consecutively;
the LED will change its blink mode (1 1 1 0 1 1 1 0) to show that the 2nd
AUX channel code is being saved. On sending the selected code with the
desired remote, LED L2 will remain steady on to indicate that programming
will be completed.
If all 120 codes have been saved, repeating the programming operation will
cause all the programming LEDs to start blinking to signal that no further
codes can be saved.
Deletion:
Use SEL to go to LED L2; activate blinking of the code to be deleted (CODE
or PEDESTRIAN or 2nd AUX channel as identified by the associated blinking
mode); press and hold down SET for > 5 s. After this interval the LED will
switch off for 2 seconds and the procedure is completed. If all CODE and
PEDESTRIAN codes are deleted, the LED will remain off.
If only PEDESTRIAN or 2nd CH codes remain stored, the LED blinking
mode will change (1 1 1 1 0 1 1 1 1 0)
Rule of the first saved Remote control:
When programming remotes the following rule is applied: if the first remote
to be saved is of the rolling code type, the receiver will subsequently accept
only rolling code remotes, thus providing enhanced anti-intrusion security;
if the first remote to be saved is of the fixed code type, the receiver will
subsequently accept both fixed code remotes and rolling code remotes.
3. CONDO:
The Condominium function means that during the opening movement or
during the pause time the control unit will not respond to commands sent
by Pushbuttons or remotes. In contrast, during the closing movement a
command sent by the Pushbuttons or the remotes will reverse the direction
COMUNELLO ®Copyright 2014 - All right reserved
Automatic
No code
ON OFF
30 sec.
Without automatic closure
ON OFF
ON OFF
ON
25