Comunello Automation QUAD - 24V - HP Instrucciones De Uso Y De Instalacion página 27

6. DS1 PARTIAL REVERSAL:
The control unit allows the operation of input DS1 to be modified. If you
want DS1 to cause a partial reversal (short reversal) of the gate leaf instead
of a total reversal, proceed as follows: ensure you have enabled Extended
Menu 1 (alternate blinking 1 0 1 0 1 0 of LED LEV) and then use the SEL key
to select blinking LED L6 and press the SET key; LED L6 becomes steady
on and the operation will be completed. Repeat the procedure if you wish
to restore the initial configuration.
7. EMERGENCY STOP = 8K2:
The control unit allows the connection of a NC Emergency Stop pushbutton
(CN2 input no.8). However, this input can be switched to an 8.2 KOhm
resistive input: ensure you have enabled Extended Menu 1 (alternate
blinking 1 0 1 0 1 0 of LED LEV) and then use the SEL key to select
blinking LED L7 and press the SET key; LED L7 becomes steady on and
programming will be completed. A change of the value read on the input
will cause the control unit to shut down irrespective of the gate movement
currently in progress. An additional gate movement command will be valid
provided the correct input value is restored and irrespective of the prior
status the control unit will execute the gate opening cycle. Repeat the
procedure if you wish to restore the initial configuration.
EXTENDED MENU 2
The control unit is factory set to allow direct selection exclusively of the main
menu functions.
If you wish to enable the functions described in Extended Menu 2, proceed
as follows: select blinking LED no.8 and press SET twice. The LED will
start blinking alternately 1 1 0 1 1 0. This means there will be 30 seconds
to select the functions of Extended Menu 2 using the SEL and SET keys;
once an additional 30 seconds have elapsed the control unit reverts to the
main menu.
L1 BRAKE
L2 DECELERATION
L3 ALWAYS CLOSE
L4 FOLLOW ME
L5 PEDESTRIAN TIME
L6 2°CH MONOSTABLE
L7 REMOTE PROG.
LEV MENU LEVEL
1. BRAKE
The control unit is factory set with the electronic brake function disabled.
If you wish to enable this function, proceed as follows: ensure you have
enabled Extended Menu 2 (alternate blinking 1 1 0 1 1 0 1 1 0 of LED LEV)
and then use the SEL key to select blinking LED L1 and press the SET key;
LED L1 becomes steady on and the operation will be completed.
With the brake enabled the control unit reduces coasting of the gate due
to inertia at the time of a stop or direction reversal command. Repeat the
procedure if you wish to restore the previous configuration.
2. DECELERATION:
As indicated above, the control unit allows a deceleration stage to be
programmed during opening and closing, while with the Automatic
Programming function the deceleration stage is included automatically.
However, if no deceleration is required it can be excluded. In this manner,
when using Automatic Programming the Deceleration stage will no longer
be included, while if the Motor Times Programming function is used the
option of programming a deceleration stage during opening and closing
will no longer be available. If, before excluding the deceleration stage it had
already been programmed using the Motor Times Programming function,
programming must be repeated from the beginning. If you wish to exclude
the deceleration stage proceed as follows: ensure you have enabled
Extended Menu 2 (blinking 1 1 0 1 1 0 of LED LEV) and then use the SEL
key to select blinking LED L2 and press the SET key; LED L1 becomes
steady on and the operation will be completed. Repeat the procedure if you
wish to restore the previous configuration.
3. ALWAYS CLOSE:
The control unit allows setting "Always Close" operation: this function, which
is programmable only if a Pause Time has already been programmed,
is activated after a power loss; if the gate open condition is confirmed,
a closing movement is started automatically, preceded by 5 seconds of
preflashing. If you wish to perform this operation mode, proceed as follows:
ensure you have enabled Extended Menu 2 (blinking 1 1 0 1 1 0 of LED
ON OFF
OFF ON
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
2 FLASHES
LEV) and then use the SEL key to select blinking LED L3 and press the
SET key; LED L3 becomes steady on and the operation will be completed.
Repeat the procedure if you wish to restore the previous configuration.
4. FOLLOW ME:
The control unit allows the "Follow me" function to be configured;
programmable only if a Pause Time has already been set, this function
reduces the Pause Time to 5 seconds after freeing the DS1 photocell,
meaning the gate re-closes 5 seconds after transit of the user. In order
to enable this function proceed as follows: ensure you have enabled
Extended Menu 2 (blinking 1 1 0 1 1 0 of LED LEV) and then use the SEL
key to select blinking LED L4 and press the SET key; LED L4 becomes
steady on and the operation will be completed. Repeat the procedure if you
wish to restore the previous configuration.
5. PED. MOT. T: (Programming of pedestrian opening motor time of
max 4 minutes)
The control unit is factory set with Motor time (Pedestrian opening) of 10
seconds without deceleration.
If pedestrian motor time must be changed, programming must be carried
out with the gate closed as follows: ensure you have enabled Extended
Menu 2 (blinking 1 1 0 1 1 0 of LED LEV) use the SEL key to select blinking
LED L5 and then press the SET key momentarily; the Operator will start the
opening movement; when the desired deceleration starting point is reached
press the SET key again; LED L5 will start blinking more slowly and the
Operator will decelerate; on reaching the desired position press SET to
terminate the Opening cycle. At this point LED L5 returns to the normal
blinking speed and the Operator restarts in the Closing movement; repeat
the operations described above for the Closing movement.
If you do not require the control unit to perform the deceleration, during
programming, when the open-close cycle has been completed press the
SET key twice consecutively rather than just once.
During programming, instead of the SET key on the control unit you can use
the button on the remote, providing the remote has been saved beforehand.
6. AUXILIARY RADIO CHANNEL OPERATING LOGIC:
The control unit allows the operating logic of the Auxiliary Radio Channel
to be selected.
The control unit is factory set with "Monostable" operation of the Auxiliary
Radio Channel. If you wish to enable "Bistable" operation proceed as
follows: ensure you have enabled Extended Menu 2 (blinking 1 1 0 1 1
0 of LED LEV) and then use the SEL key to select blinking LED L6 and
press the SET key; LED L6 becomes steady on and the operation will be
completed. If you wish to enable "3 Minutes Timed" operation, repeat the
operation described above; pressing the SEL key twice (LED L6 will blink
rapidly) rather than once. Repeat the procedure if you wish to restore the
initial configuration.
7. REMOTE RADIO CONTROL PROGRAMMING:
The control unit allows the transmission code to be programmed remotely
without acting directly on the control unit SEL key.
Remote programming of a Radio remote control is performed as follows:
send, continuously for a time in excess of 10 seconds, the code of a
previously saved remote control; at the same time the control unit switches
to programming mode as described above for the LED L2 in the main
menu. If a previously saved code is transmitted continuously the control
unit will enter programming mode of a new pedestrian code and LED L2 will
blink as though acquisition of the pedestrian code were active (1 1 0 1 1
0 1 1 0); if the code is associated with the 2nd CH/AUX input the LED will
blink as though acquisition of the 2nd CH code were active (1 1 1 0 1 1 1 0
1 1 1 0). To enable the remote programming function, proceed as follows:
ensure you have enabled Extended Menu 2 (blinking 1 1 0 1 1 0 of LED
LEV) and then use the SEL key to select blinking LED L7 and press the
SET key; LED L7 becomes steady on and the operation will be completed.
Repeat the procedure if you wish to restore the initial configuration.
EXTENDED MENU 3
The control unit is factory set to allow direct selection exclusively of the main
menu functions.
If you wish to enable the functions described in Extended Menu 3, proceed
as follows: select blinking LED LEV and press SET 3 times. The LED will
start blinking alternately 1 1 1 0 1 1 1 0. This means there will be 30
seconds to select the functions of Extended Menu 3 using the SEL and
SET keys; once an additional 30 seconds have elapsed the control unit
reverts to the main menu.
COMUNELLO ®Copyright 2014 - All right reserved
27