Preset Programs - STEINEL PROFESSIONAL HG 2320 E Manual De Instrucciones

HG 2320 E
Technical Specifications HG 2320 E
Item No. 110025598
Temperature 120°F - 1200°F (49°C - 649°C)
Airflow Continuously variable 4-13 cfm
(+/- 0.5)
Switch Cool air stage,
variable temperature & airflow
Programs Four customizable pre-set
temperature/airflow programs
Output 1600 watts
Voltage 120 VAC / 60 Hz
Amps 13.3
Power Cord Industrial grade rubber, length: 6 ft
Nozzle Diameter 1.30" (33.02 mm)
Dimensions 9.96" x 3.41" x 7.87" (l x w x h)
Net Weight 2.19 Ibs (35.10 oz)
Single Sell Pack Dimensions: 10.20" x 3.54" x 9.33"
Weight: 2.60 Ibs (41.66 oz)
Warranty One year limited
(only HG 2320 E)
(only HG 2320 E)
English
- 6 -
HG 2320 E
1. Operation
The tool is switched on and off at a two-stage switch on the back of the grip handle. The toggle is used for
controlling temperature and airflow respectively for speed.
2. Setting temperature
The hot air tool is factory set to display the temperature in °F. Stage 1 is the cooling stage, temperature is
always 120 °F. Use the cooling function for drying paint, cooling workpieces or for cooling the nozzle before
changing the accessory attachment. In stage 2 temperature is continuously variable over a range of 120 °F -
1200 °F on the control panel with LCD display. The actual temperature is measured at the nozzle outlet and
indicated on the display. The toggle is used as an input button with plus/minus function. The temperature
setting range begins at 120 °F and ends at a maximum of 1200 °F. Briefly pressing the "+/–" toggle increas-
es or reduces the temperature setting in 10° steps. Keeping the toggle pressed speeds up the temperature
setting process. Once the temperature has been set, the tool takes a few seconds to reach temperature
(depending on speed/airflow). The temperature setting selected is shown on the display for 3 seconds. The
display then shows the current actual temperature. The "°C/°F" symbol continues to flash until the selected
temperature is reached. If you want to alter the setting, simply press the toggle again to increase or reduce
the temperature. After switching off, the hot air tool stays in the last setting.
3. Setting airflow rate
To change the airflow rate, first press the "airflow" button; the fan symbol flashes. Now use the toggle to set
the airflow rate. The airflow rate setting mode automatically closes if the airflow rate setting is not changed
within 5 sec. Pressing the airflow button again after setting the airflow rate immediately closes the airflow rate
setting mode. The airflow rate can be varied from a minimum of
4. Programming mode [P]
Besides normal operating mode, the HG 2320 E also has four factory-set programs for the most frequent
jobs. Four programs are factory-set for the most common types of work. Press button "P" for programming
mode. Number 1 is displayed for program 1. Continuing to press the program button will take you to
programs 2-4. Pressing the button again will return the tool to normal operation. See page 6.

Preset Programs

Programs °F / °C CFM Application
1 265 °C / 510 °F 7.3 cfm Shaping plastic
pipes
2 350 °C / 660 °F 9.0 cfm Welding plastics
3 460 °C / 860 °F 11.4 cfm Paint stripping
4 560 °C / 1040 °F 10.8 cfm Soldering
5. Memory function [S]
The values selected for the four programs can be changed and memorized at any time. To do this, first
press the program button "P" until the display shows the program you wish to change. Set the temperature
and airflow rate you require. Memory symbol
selected has been changed. To memorize this setting in the user program selected, press and hold down
the program selector button. The memory symbol continues to flash for approx. 2 sec. The settings entered
are saved once the memory symbol stays on all the time. To return to normal operation, press the program
button until the program symbol disappears from the display. See page 6.
English
to a maximum of 13 cfm (+/- 0.5 cfm).
4 cfm
on the LCD flashes to indicate that the user program
- 7 -