STEINEL PROFESSIONAL HG 2320 E Manual De Instrucciones página 6

HL 1620 S
Technical Specifications HL 1620 S
Item No. 110023455
2 Stage Switch 575 °F (302°C) / 8 cfm
950 °F (510°C) / 13 cfm
Output 1300 watts
Voltage 120 VAC / 60 Hz
Amps 10.8
Power Cord Industrial grade rubber, length: 6 ft
Nozzle Diameter 1.30" (33.02 mm)
Dimensions 9.92" x 3.37" x 7.87" (l x w x h)
Net Weight 1.65 Ibs (26.4 oz)
Single Sell Pack Dimensions: 10.20" x 3.54" x 9.3"
Weight: 2.06 Ibs (32.98 oz)
Warranty One year limited
The tool is switched on and off at the two-stage switch on the back of the grip handle. Airflow and temperature
can be adjusted between 2 settings. Stage 1 reaches 575 °F at an airflow of 8 cfm, stage 2 reaches 950 °F at
13 cfm.
Changing the power cord
Important! Disconnect tool from power supply.
If the power cord is damaged, it can easily be changed without opening the housing.
1. Undo screw and pull off cover cap
d a .
2. Release cable grip
.
b
3. Undo mains terminals c
.
4. Pull out cable .
e
5. Insert new cable and secure in reverse order (Firmly screw down mains terminals etc.).
English
- 10 -
Applications
Shrink tubing on cables:
The shrink tubing is slipped over the section you want to insulate and heated with hot air. The tubing shrinks by
approx. 50% in diameter to give a sealed union. Shrinking is particularly fast and even using reflector nozzles.
Sealing and stabilizing cable breaks, insulating soldered joints, gathering cable runs, sheathing terminal blocks.
Forming PVC:
Sheeting, piping or ski boots can be softened and formed with hot air.
Thawing:
Water pipes, frozen door locks, steps. Gently thaws and dries all in one go.
Soldering:
First, clean metal parts you want to join. Then, using hot air, heat the point you want to solder and offer up the
soldering wire. Use flux or a soldering wire with a flux core to prevent oxide forming.
Welding and joining plastic:
All parts being welded must be of the same plastic material. Use an appropriate welding rod.
Joining plastic sheeting:
The sheets are overlapped and welded together. A slit nozzle is used to direct hot air under the overlap, then the
two sheets are firmly pressed together with a feed roller.
Also possible: Repairing PVC tarpaulins by overlap welding with a slit nozzle.
Shaping:
Ski boots and sports shoes can be shaped for a perfect fit.
Desoldering:
Electronic components are detached quickly and neatly from circuit boards with a reduction nozzle.
Welding sheeting:
The sheets are overlapped and welded together. A slit nozzle is used to direct hot air under the overlap, then the
two sheets are firmly pressed together with a feed roller.
Also possible: Repairing PVC tarpaulins by overlap welding with a slit nozzle.
Plastic types:
Material Application types
Rigid PVC Piping, fittings, boards, building profiles,
technical molded components, etc.
Welding temperature
550 - 650 °F (290 - 345 °C)
Plasticized PVC Floor coverings, wallpaper, hoses, sheets,
tools, etc.
Welding temperature
550 - 650 °F (290 - 345 °C)
Plasticized PE Domestic and electronic items, toys,
(LDPE) bottles, etc.
Polyethylene Welding temperature
450 - 550 °F (230 - 290 °C)
Hard PE Baths, baskets, canisters, insulating materials,
(HDPE) piping, cellar shafts, transport containers,
Polyethylene waste bins, etc.
Welding temperature
550 - 650 °F (290 - 345 °C)
PP HT drainpipes, plastic chairs, packaging, car
Polypropylene components, equipment housing, technical
moldings, battery boxes, etc.
Welding temperature
450 - 550 °F (230 - 290 °C)
Car components, equipment housing,
ABS
suitcases
Welding temperature
625 - 725 °F (330 - 385 °C)
English
Distinguishing characteristics
Incineration test: carbonizes in the flame and
extinguishes on its own
Smoke odor: pungent, of hydrochloric acid
Drop test: crashing
Incineration test: smoking, yellowish-green
flame
Smoke odor: pungent, of hydrochloric acid
Drop test: silent
Incineration test: light, yellow flame,
drops continue to burn
Smoke odor: resembles an extinguished
candle
Drop test: dull
Incineration test: light, yellow flame,
drops continue to burn
Smoke odor: resembles an extinguished
candle
Drop test: crashing
Incineration test: light flame with a blue core,
drops continue to burn
Smoke odor: pungent odor of paraffin
Drop test: crashing
Incineration test: black, fluffy smoke
Smoke odor: sweetish
Drop test: crashing
- 11 -