Programming The Automation; Memorising Devices Connected By Means Of "Bus" Cable And Leaf Travel Limit Positions "0" And - moovo XW4 Instrucciones Y Advertencias Para La Instalación Y El Uso

WARNINGS for programming:
• Always read the procedure first and then perform the operations in the
correct sequence.
• In this manual the transmitter keys are identified by means of numbers.
To check the correspondence of numbers and the transmitter keys see
fig. 52.
52
T1
T3
STEP 9
9.1 – MEMORISING DEVICES CONNECTED BY MEANS
OF "BUS" CABLE AND LEAF TRAVEL LIMIT
POSITIONS "0" AND " 1".
After ensuring correct operation of the control unit, it must be pro-
grammed as described in the sequence below:
Note – During this procedure, the user can exit the process at any time
(without saving the operations performed) by pressing "P1" once on the
control unit (fig. 51). In particular, from point 07 onwards, the user can
also exit the procedure by activation of a safety device (photocell or oth-
er...).
01. (on Gate)
Release the two gearmotors by means of the special release key (see
chapter "Manually releasing or locking the gearmotor" in the
TECHNICAL DOCUMENTATION) and manually move the two gate
leafs to the position shown in fig. 53. Then lock the two gearmotors
again.
53
Leaf 1
02. (on the Control unit)
Pres and hold the key "P1" on the Control unit for at least 5 seconds
until the green Led turns off and the red led illuminates (this remains
lit through to the end of the procedure). Then release the key and pro-
ceed as follows:
03. (on safety Photocells)
Note – The time available for this check is unlimited.
Check correct operation of these types of photocells, ensuring that
the relative Led flashes slowly. Otherwise if it is lit or off, correct align-
ment between the photocells attempting to obtain a flashing frequen-
cy that is slow as possible (the slower the flashing speed, the better
the photocell alignment).
• slow flashing light = correct photocell alignment;
• light permanently lit = incorrect alignment (revise photocell align-
ment);
22 – English

PROGRAMMING THE AUTOMATION

• light off = photocells installed incorrectly (check "Bus" connection of
photocells).
04. (on control Photocells)
Activate this type of photocell (if fitted on the system), interrupting the
beam once only. Successful learning is confirmed by the flashing light
(1 flash) and the keypad (1 beep), if fitted on the system.
05. (on the keypads)
Activate the keypads (if fitted on the system) by pressing any key on
each one as required.
T2
Successful learning is confirmed by 2 beeps at short intervals, emit-
ted by the keypad and 1 flash of the flashing light, if fitted on the sys-
tem.
T4
06. (on the Control unit)
Pres and hold the key "P1" on the Control unit for at least 5 seconds
until the green Led turns off. Then release the key.
07. (on Gate)
Note – the manoeuvres that follow enable the control unit to auto-
matically memorise the positions of point "0" (total closing) and point
"1" (total opening), as shown in fig. 54.
54
At this point the Control unit automatically activates 3 manoeuvres,
also indicated by the flashing light:
1 - Closure of Leaf 2, followed by closure of Leaf 1.
2 - Opening of the two leafs.
3 - Closing of the two leafs.
At the end of the last manoeuvre, the red led turns off (= procedure
completed) and then resumes flashing at regular intervals
CAUTION! – As soon as the first manoeuvre starts, check imme-
diately that:
a - Leaf 2 moves before Leaf 1;
b - Leaf 2 moves in the Closing direction.
If the results of these checks do not conform with specifications, stop
the procedure immediately by pressing P1 on the control unit once.
Then identify the problem "a" with reference to STEP 6.1, and prob-
lem "b" by inverting the electrical wires connected to terminals "M+"
Leaf 2
and "M-" on the control unit. Then repeat the entire procedure 9.1
Memorising other devices connected by Bus cable at a later
date
If in future the user decides to install and memorise other devices con-
nected to the control unit by means of the Bus, and procedure 9.1 has
been completed previously, the new devices can be memorised using
the same procedure, starting from point 01 through to point 06. On com-
pletion, press P1 once on the control unit to complete the memorisation
process.
Positions "0"
Positions "1" Positions "1"