Using The Machine; Completing Assembly; Machine Setup; Machine Assembly - GGP ITALY SH 2500 Manual De Instrucciones

EN
OPERATING INSTRUCTIONS
NOTE - The number which precedes each paragraph
links the references in the text to the respective illustra-
tions (listed on page 2 and following pages).

1. COMPLETING ASSEMBLY

NOTE - The machine can be supplied with some
pre-assembled parts.
WARNING - Unpacking and completing the assem-
bly should be done on a flat and stable surface,
with enough space for handling the machine and its
packaging, always using suitable equipment.
Disposal of the packaging should be done in accor-
dance with the local regulations in force.

1.1 Machine assembly

Grasp the working head (1) as indicated and position it
over the frame (2), taking care to insert the protruding part
(3) in its slot (4). Fully tighten the four knobs (5).
Assemble the wheels (6), using the pins (7), washers (8)
and split pins (9) in the indicated sequence.
Apply the wheel covers (10) inserting the tabs (11) in
their slots (12).
IMPORTANT - When assembly is completed, the di-
stance between the pressure plate and the shredding
roller must be adjusted as indicated at point 4.1.

2. CONTROL DESCRIPTION

2.1 Motor control

The motor is controlled by two buttons:
– Green button (1-I ) = Run
– Red button (2-O) = Stop
The tool will switch off in the event of a power shortage.
Press the green button (1) again to restart the motor.
2.2 Rotation direction switch
The motor rotation direction is controlled by two buttons:
– Black button (3-▼) = O perating rotation direction, fa-
– Black button (4-▲) = R otation in opposite direction to
When the motor is started, the operating rotation direction
is automatically set which favours material feeding.
vour ing material feeding.
free jammed material; a led (5) li-
ghts up to indicate that rotation is
in the opposite direction.

3. USING THE MACHINE

IMPORTANT:
• U se the machine on firm level ground, keeping feet
at the same level as the wheels.
• W hen starting the machine there can be momentary
drops in voltage. Make sure that its impedance is lower
than 0.42 ohm to prevent disturbances to other equip-
ment connected to the mains supply.
• If the motor stops because it is overheated while wor-
king, you must wait about 5 minutes before restarting it.
3.1 Machine set-up
Fit the collection box (1) in the space beneath the machine
and pull the safety handle (2) up to lock it and enable the
motor to be started.
If the handle is not positioned properly, the motor will not
start.
3.2 Machine connections
Properly insert the extension lead socket (11) to the ma-
chine plug (12) as indicated, then insert the extension
lead plug in the mains socket (13).
3.3 Motor start-up and operating modes
Press the green button (1-I ) to start the motor. Always
feed the material to be shredded from the right side
through the hopper's feed opening (2). If necessary, use
the provided plunger (3) to help push material through.
Advice for shredding
• Avoid shredding wet material.
• S trip branches with too many ramifications and remove
the side shoots.
• Do not shred branches with a diameter exceeding 4 cm;
it may be necessary to reduce the maximum diameter
of branches to be shredded according to wood type
and freshness.
• A lways feed small quantities of material in order to not
clog the feeding hopper.
• Avoid blocking the discharge chute to prevent shredded
material from backing up through the feeding hopper.
• S hred garden waste only in small quantities, particularly
when humid or wet; alternate it with branches to prevent
clogging.
• Do not shred kitchen waste or other material with a
non-solid consistency.
Important recommendations
• D o not shred excessively long branches to prevent inju-
ries from branches that may lash out uncontrollably.
25