Operation - Black Max BMi1000 Manual Del Operador

NOTICE:
The spark arrestor on this product has not been evaluated
by the USDA Forest Service and cannot be used on U.S.
forest lands. In addition, product users must comply
with Federal, State, and local fire prevention regulations.
Check with appropriate authorities. Contact customer
service or a qualified service center to purchase a
replacement spark arrestor.
NOTICE:
Before each use, inspect the entire product for damaged,
missing, or loose parts such as screws, nuts, bolts,
caps, etc. Tighten securely all fasteners and caps and
do not operate this product until all missing or damaged
parts are replaced. Please contact customer service or
a qualified service center for asssistance.
APPLICATIONS
This generator is designed to supply electrical power for
operating compatible electrical lighting, appliances, tools,
and motor loads.
BEFORE OPERATING THE UNIT
 Only use OUTSIDE and at least 20 feet away from
windows, doors, and vents as recommended by the U.S
Department of Health and Human Services Centers for
Disease Control and Prevention. Your specific home and/
or wind conditions may require additional distance.
 NEVER use inside a home or garage, EVEN IF doors and
windows are open.
 Always position the generator on a flat firm surface.
SPECIAL REQUIREMENTS:
There may be General or State Occupational Safety and
Health Administration (OSHA) regulations, local codes or
ordinances that apply to the intended use of the generator.
Please consult a qualified electrician, electrical inspector, or
the local agency having jurisdiction:
 In some areas, generators are required to be registered
with local utility companies.
 If the generator is used at a construction site, there may
be additional regulations which must be observed.
LED DISPLAY
See Figure 2.
Power:
The power indicator will light when the generator is on and
the receptacle is operational.
NOTE: If the generator is overloaded, the power indicator
light will go off.
All manuals and user guides at all-guides.com

OPERATION

Overload:
The overload indicator will blink when the generator's
maximum wattage/amperage is reached. If the wattage/
amperage capacity is exceeded, the LED will become solid
and the unit's output will automatically shut down. To reset
the generator, remove all loads from the generator and press
the reset button. Once the overload indicator goes out, add
loads back one at a time, being careful not to exceed the
generator's wattage rating.
Lubricant:
The oil indicator will light and the engine will automatically
shut off whenever the lubricant level in the engine becomes
low. The engine may not be restarted until sufficient engine
lubricant has been added to the generator.
NOTE: It is normal for the indicator lights to illuminate and/
or blink each time the engine is started. Once the engine
warms up, the lights should default to the pattern above.
CHECKING/ADDING LUBRICANT
See Figures 3 - 4.
NOTE: If a separate engine manual is provided for this
product, please follow the instructions provided in the
engine manual instead of the information listed below.
Engine lubricant has a major influence on engine perfor-
mance and service life. For general, all-temperature use,
SAE 10W-30 is recommended. Always use a 4-stroke motor
lubricant that meets or exceeds the requirements for API
service classification SJ.
This engine comes with a feature that will shut off the engine
when a specific lubricant level is not maintained. The engine
will not restart until an appropriate lubricant level is reached.
NOTE: Non-detergent or 2-stroke engine lubricants will
damage the engine and should not be used.
 Loosen the screw at the top of the engine maintenance
 Unscrew the oil cap/dipstick and remove.
 Wipe dipstick clean and re-seat in hole; do not re-thread.
 Remove dipstick again and check lubricant level.
 If level is low, add engine lubricant until the fluid level
 Replace and secure the oil cap/dipstick.
 Replace the engine maintenance cover and reinstall the
Page 12 — English
NOTICE:
Attempting to start the engine before it has been properly
filled with lubricant will result in equipment failure.
cover. Remove cover and set aside.
Lubricant level should fall between the minimum and
maximum marks on the dipstick.
rises between the minimum and maximum marks on the
dipstick.
screw to secure.