Series Recording; Alarm Recording - Samsung SVR-24JP Instrucciones De Uso E Instalación

SERIES RECORDING

This is a convenient function in which when two or more VCRs are
connected the second unit starts recording when the tape on the first unit
reaches the end.
Connecting Operating
method method
• Select to No. 4 in the MENU
Refer to the
• Select to "ON" for SERIES
connection
using the SHIFT
method for
button.
series recording
(page 37)
REFERENCE
When pressing the RESET button
RESET button
• Use this button when the VCR or • All the entered information such as reserve recording set
time, current time, and alarm information is erased.
display does not operate normally even
• The power is turned off, and there is no picture at all. When
though the power is turned on.
• The RESET button is on the right side of the power is turned on again,
display of the screen.
the Front Panel.
• Press the RESET button using a ball • The current time is erased and must be reset.
point pen or a pencil.
31
Description
of operation
• When the tape in the first unit
arrives at its end during
❷ ! ❷ and ❿ ❿ recording, the second unit begins
recording. When the tape in the
second unit arrives at its end and
during recording, the next unit
begins recording if connected.
• When the series recording mode
is selected, the second unit
performs recording even if the
power is turned off.
• As a constant alarm sounding,
you can clear it by only pressing
any key.
flashes on the
2001-1-1 MON
12:00:00 L3H

ALARM RECORDING

If the VCR is connected to equipment with an alarm output such as a frame switcher,
motion detector or door switch, the VCR will function according to the time and mode
selected on the ALARM REC menu when an alarm is received.
SVR-24JP has only L3H/L12H/L24H mode for ALARM REC.
The below diagram is set L3H mode for ALARM REC.
L12H~960H
L3H
(L12H~L24H)*
mode recording
mode recording
Timelapse recording Alarm recording
Start of Enter of Enter of alarm reset
recording alarm signal or over selected time
Connecting Operating
method method
Connect the alarm • Select to MODE and
output equipment
DURATION on
as follows;
ALARM REC SETUP
in setting MENU3.
(Refer to ALARM
1 ALARM IN 2 ALARM OUT 3 ALARM RESET 4 ERROR OUT 5 TRIGGER OUT
6 TAPE END OUT 7 SERIES OUT 8 GND 9 SERIES IN 10 1 SHOT RECIN
REC SETUP, page 16)
1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 9 9 10 10
• When connecting with
IN
IN OUT
FRAME SWITCHER, it
OUT
is convenient, if the
AUDIO VIDEO
switch is placed in
automatic position.
GND
ALARM
VIDEO
OUT OUT
ALARM
RESET
(Refer to page 37)
L12H~960H
L3H
(L12H~L24H)*
mode recording
mode recording
Timelapse recording Alarm recording
Enter of
alarm signal
Description of
operating
• AUTO: The alarm recording time is
automatically determined by input of
the alarm signal. (1 minute)
• 20sec~5min: Alarm recording is made
for 20 seconds~5 minutes after input of
the alarm signal.
• TAPE END: Alarm recording is made
up to the end of the tape after input of
the alarm signal.
• When the alarm signal is entered, the
on the front display is turned on.
• When the alarm recording is ended,
the on the front display flashes.
• When you want to cancel the alarm
during alarm recording, make a
connection between the alarm release
and the alarm grounding for more than
0.5 second, when the alarm release is
entered, the alarm recording is
stopped.
• When an alarm signal is received and
the BUZZER ON is selected in the
menu, the alarm sounds continuously.
To silence the buzzer, press any
button.
32