General Information; Unpacking; Assembly; Operation - Generac GP 3250 Manual Del Propietário

General Information

1.1 UNPACKING

• Remove all packaging material.
• Remove separate accessory box.
• Remove the generator from carton.
1.1.1 ACCESSORY BOX
Check all contents. If any parts are missing or damaged, locate an
authorized dealer at 1-888-436-3722.
• 1 - Owner's manual
• 1 - Oil SAE 30
• 3 - Product Registration Cards (English, Spanish, French)
• 2 - 8" WHEELS
• 1 - Axle
• 1 - Frame Foot
• 1 - Handle with grip
• 1 - Hardware Bag
1 - Plastic Spacer
1 - Handle Bracket
2 - Rubber Bumpers
2 - Cotter Pins
2 - M8-1.25 Hex Flange Nuts

1.2 ASSEMBLY

The generator requires some assembly prior to using it. If problems
arise when assembling the generator, please call the Generator
Helpline at 1-888-436-3722.
1.2.1 ASSEMBLING THE ACCESSORY KIT
The wheels are designed to the unit to greatly improve the
portability of the generator.
The wheels are not intended for over-the-road-use.
1. Refer to Figure 1 to install the wheels as shown.
• Slide the axle through the frame brackets.
• Slide on the wheels then install the cotter pins.
2. Refer to Figure 1 to install the wheel bumpers as shown.
• Secure the two rubber bumpers to the frame foot
using two M8-1.25 Hex Flange Nuts (if not already
assembled).
• Place the frame foot under the frame and secure with two
M8-1.25 x 16 bolts.
3. Refer to Figure 2 to install the handle assembly as shown.
• Install the handle bracket to the frame using two M8-1.25
x 40 bolts (if not already assembled).
• Slide the plastic spacer onto the handle assembly then
align with the holes in the handle bracket (if not already
assembled).
• Secure the handle assembly to the handle bracket using
the M6-1.0 x 40 bolt and one M6-1.0 hex flange nut.
4
2 - M8-1.25 x 40 Bolts
1 - M6-1.0 x 40 Bolt
2 - M8-1.25 x 16 Bolts
1 - M6-1.0 Hex Flange Nut
NOTICE:
Figure 1 – Wheel Assembly
Figure 2 – Handle Kit
1x HANDLE BRACKET
1x M6-1.0X40 BOLT
1x PLASTIC SPACER
1x HANDLE W/GRIP

2.1 KNOW THE GENERATOR

Read the Owner's Manual and Safety Rules before operating
this generator.
Compare the generator to Figures 3 through 6 to become
familiarized with the locations of various controls and adjustments.
Save this manual for future reference.
1. 120 Volt AC, 20 Amp, Duplex Receptacle – Supplies electrical
power for the operation of 120 Volt AC, 20 Amp, single-phase,
60 Hz electrical lighting, appliance, tool and motor loads.
2. 120/240V AC, 20 Amp Locking Receptacle – Supplies
electrical power for the operation of 120 and/or 240 volt AC,
20 amp, single-phase, 60 Hz, electrical lighting, appliance,
tool and motor loads.
3. Circuit Breakers (AC) – Each receptacle is provided with a
2-pole, 14 amp circuit breaker to protect the generator against
electrical overload.
4. Air Filter – Filters intake air as it is drawn into the engine.
5. Choke Knob – Used when starting a cold engine.
6. Fuel Tank – Tank holds 4 U.S. gallons of fuel.
7. Grounding Lug – Ground the generator to an approved earth
ground here. See "Grounding the Generator" for details.
8. On/OFF Switch – Controls the operation of the generator.
M8-1.25 x 40
BOLTS
1 X M6-10 HEX FLANGE NUT