Miche SUPERTYPE440RCDX Manual De Uso Y Mantenimiento página 7

Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

HUBS
2
Warning
!
If you have any doubt whatsoever your service-repair ability,
please take your bicycle to a qualified repair shop.
Before any maintenance operations on your wheels, always
wear gloves and protection glasses.
Use original spare parts exclusively provided by
Fac Michelin S.r.l.
When replacing any broken sealed bearings please ensure sealed
bearing correct measure and specification are used.
Rear hub
Right side
26x17x5 (6803)
Left side
26x17x5 (6803)
The Supertype DX hubs are easy to maintain. To do it, proceed
as follows:
FRONT HUB
The front hub does not require any particular maintenance.
For any extraordinary maintenance and replacement of bearings,
follow these simple steps:
• Remove the contact item (A) (Fig. 1)
• On the same side from which you removed the contact item,
insert a 12mm Allen wrench (M) on the hub pin and, using a
classic 17mm wrench (N), unscrew the contact item (B) counter-
clockwise (Fig. 2)
• Remove the axle from the side of the disc brake.
• Once the axle has been removed, you can replace the bearings:
• Use a special puller for 17mm holes and remove both bearings (S)
from their seat (Fig. 3)
• Once these have been replaced, proceed fitting the new bea-
rings:
• Using a special tool, insert both new bearings in their seat, che-
cking the correct smoothness.
• Insert the hub axel (C) again and tighten the contact item (B) with
the 17mm wrench (N) at the tightening torque of 15Nm. (Fig. 2)
• If necessary adjust the hub by working on the ring (F) (Pic. 2):
• Unlock the grub screw (I) with a allen wrentch 2mm (L).
• Turn the ring in clock sense to drop the sliding, and in anti-clock
sense to rise the sliding.
• Lock the screw (I).
• Check the sliding of the wheel.
Please check that the hub is correctly tightened and closed, fai-
lure to do so could lead to a serious or fatal accident.
Warning
!
Use original spare parts exclusively provided by Fac Michelin S.r.l.
Any modification or alteration (also graphic) of the product with
non-original spare parts or spare parts not delivered directly
by Fac Michelin S.r.l., involves the expiration of the guarantee.
Front hub
26x17x5 (6803)
26x17x5 (6803)
REAR HUB
The rear hub requires cleaning and lubrication of the ratchets in
the freewheel body.
For any maintenance:
• Insert allen wrentch 12mm (M) on right side of the hub (Pic. 4).
• Using adjustable wrentch (N), unscrew left stop (O)
• Extract the axel of rear hub with the freehub body (E).
If necessary at this point you can:
• Change the bearings (S).
• Grease the cogs with low density grease.
• Extract from the axel the freehub body with the relative spacer
(Z) continue the cleaning process of hub.
• Warning: the bearings of the freehub body and no replaceable.
• Re-fit the axel (C) inside hub body with the spacer (Z). Take care
to position of the pawls (Pic.4).
• Insert allen wrentch 12mm (M) on right side of the hub (Pic.6).
• Stopping left stop (O) with adjustable wrentch (N) locking at 15
Nm (Pic. 6)
• If necessary adjust the hub by working on the ring (H) (Pic. 6):
• Unlock the grub screw (I) with a allen wrentch 2mm (L) (Pic. 6).
• Turn the ring in clock sense to drop the sliding, and in anti-clock
sense to rise the sliding.
• Lock the screw (I) (Fig. 6
• Check the sliding of the wheel.
Please check that the hub is correctly tightened and closed, fai-
lure to do so could lead to a serious or fatal accident.
Warning
!
Use original spare parts exclusively provided by Fac Michelin S.r.l.
Any modification or alteration (also graphic) of the product with
non-original spare parts or spare parts not delivered directly
by Fac Michelin S.r.l., involves the expiration of the guarantee.
SPOKES
3
The spokes used for the assembly of the wheels have the following
sizes and characteristics.
Supertype 440RC DX
Right side
Left side
CHANGE A SPOKE
Warning
!
If you have any doubt whatsoever your service-repair ability,
please take your bicycle to a qualified repair shop.
Before any maintenance operations on your wheels, always
wear gloves and protection glasses.
Rear wheel Front wheel
270 mm
266 mm
262 mm
270 mm
7

Publicidad

Tabla de contenido
loading

Tabla de contenido