Before Starting The Equipment; Attachment - Parkside PZKS 2000 B2 Instrucciones De Utilización Y De Seguridad

• Try to keep emissions as low as possible, for example by
limiting your working time. In this regard, all the operational
cycle phases must be taken into consideration (such as the
times when the tool is switched off or running idle).

8. Before starting the equipment

• Open the packaging and remove the device carefully.
• Remove the packaging material as well as the packaging
and transport bracing (if available).
• Check that the delivery is complete.
• Check the device and accessory parts for transport damage.
• If possible, store the packaging until the warranty period has
expired.
ATTENTION
The device and packaging materials are not toys!
Children must not be allowed to play with plastic
bags, film and small parts! There is a risk of swal-
lowing and suffocation!
• The equipment must be set up where it can stand securely.
Secure the machine on a workbench or a base frame with 4
screws (not included in delivery) using the holes on the fixed
saw table (15).
• Pull out the pre-installed tilt protection (36) completely and
secure it with an Allen key (D).
• Adjust the adjusting screw (38) to the level of the tabletop to
avoid wobbling of the machine.
• All covers and safety devices have to be properly fitted be-
fore the equipment is switched on.
• It must be possible for the blade to run freely.
• When working with wood that has been processed before,
watch out for foreign bodies such as nails or screws, etc.
• Before you press the ON/OFF switch check that the saw
blade is fitted correctly. Moving parts must run smoothly.
• Before you connect the equipment to the power supply make
sure the data on the rating plate are dentical to the mains
data.
8.1 Checking the moving saw blade guard safety
device (5)
The saw blade guard protects against accidental contact with
the saw blade and from chips flying around.
Check function
To do so, fold the saw downwards:
• The saw blade guard must provide free access to the saw
blade without touching other parts.
• When folding the saw upwards into the starting position, the
saw blade guard must cover the saw blade automatically.

9. Attachment

9.1 Attaching the crosscut, drag and mitre saw
(fig.1/2/4/5)
• In order to adjust the rotary table (14), loosen the handle
(11) approximately 2 turns and pull up the latched position
lever (35) with your index finger.
• Turn the rotary table (14) and pointer (12) to the desired
angle measurement on the scale (13) and use the handle
(11) to secure it.
• By slightly pushing down the machine head (4) while pull-
ing out and removing the locking bolt (23) from the motor
mount, the locking bolt (23) will be secured in the top posi-
tion and the saw will be unlocked from the bottom position.
• Turn the locking bolt (23) 90 degrees to secure it in the un-
locked position.
• Swing the machine head (4) up.
• It is possible to secure the clamping devices (7) to the left or
right on the fixed saw table (15). Insert the clamping devices
(7) in the holes on the rear side of the stop rail (16) and se-
cure it with the star grip screws (7a). For 0°- 45° mitre cuts,
the clamping device (7) must only be mounted on the right
side (see fig. 11-12).
• It is possible to tilt the machine head (4) a max. 45° to the
left by loosening the set screw (22).
• Workpiece supports (8) must always be secured and used
during work. Set the desired table size by loosening the set
screw (9). Then tighten the set screw (9) again.
9.2 Sawdust bag (fig. 1/22)
The saw is equipped with a debris bag (17) for sawdust and
chips.
Squeeze together the metal ring on the dust bag and attach it
to the outlet opening in the motor area.
The debris bag (17) can be emptied by means of a zipper at
the bottom.
9.2.1 Connection to an external dust extractor
• Connect the vacuum hose with the dust extraction spout.
• The industrial vacuum cleaner must be suitable for the mate-
rial being worked.
• When vacuuming dust that is especially detrimental to health
or carcinogenic, use a special vacuum cleaner.
9.3 Precision adjustment of the stop for crosscut
90° (fig. 1/2/5/6)
Tools required:
- Allen key 6 mm
- Open-ended spanner SW13 (not included in the scope of
delivery)
• No stop angle included.
• Lower the machine head (4) and secure it using the locking
bolt (23).
• Loosen the set screw (22).
• Position the angle stop (A) between the saw blade (6) and
the rotary table (14).
• Loosen the lock nut (26a).
• Adjust the adjusting screw (26) until the angle between the
saw blade (6) and rotary table (14) is 90°.
• Tighten the lock nut (26a) again.
• Subsequently check the position of the angle indicator. If
necessary loosen the pointer (19) using a Philips screwdriv-
er, set to position 0° on the angle scale (18) and re-tighten
the retaining screw.
GB/MT 53