Visonic MCT-211 Manual Del Usario

MCT-211
English Waterproof PowerCode Wrist/Pendant Transmitter
Transmisor Impermeable de Pulsera PowerCode
Español
Portuguese Transmissor Impermeável de Pulseira PowerCode
ENGLISH
1. INTRODUCTION
The MCT-211 is a miniature waterproof neck or wrist-worn
transmitter, designed for use in advanced, high security alarm and
remote control systems. Transmission is initiated by depressing the
pushbutton at the center of the unit. When activated, the transmitter
sends out a 24-bit ID code and an alarm code, both identifiable by
compatible PowerCode type receivers. The ID code assigned to each
transmitter is unique and virtually impossible to reproduce.
All MCT-211 units are supplied with a wrist band and neck strap.
They can be worn on the wrist or around the neck.
An LED lights during transmission, indicating that the battery voltage
exceeds 2.4 V approximately.
If the LED does not light (in 315 & 433 MHz versions), flashes (in
868.95 MHz version) or flashes once then goes out (in 869.2125 MHz
version) during transmission, the battery must be replaced
immediately. In addition, a transmitter in which the battery is low will
automatically add a "low battery" code to its outgoing digital message.
Compatible receivers are designed to identify this code and operate
audible, visual or other alert devices.
2. SPECIFICATIONS
Frequency (MHz): 315, 433.92, 868.95, 869.2125 (FSK), 869.2375
or other frequencies according to local requirements.
Modulation: ASK (ON-OFF keying) or FSK
Transmitter ID: 24-bit digital word, over 16 million possible code
combinations, pulse width modulation.
Total Message Length: 36 bits
Minimum Transmit Duration: 2 sec
Power Supply: 3-volt Lithium cell (Sanyo type CR-2025 or equivalent).
Nominal Battery Capacity: 150 mAh
Battery Life Expectancy: 3 years (for typical use)
Battery Supervision:
Good battery - LED lights steadily upon activation.
Low battery - LED does not light (in 315 & 433 MHz versions) upon
activation.
- LED flashes (in 868.95 MHz version) upon activation.
- LED flashes once then goes out (in 869.2125 MHz version) upon
activation.
Note: If transmission is still possible despite the battery condition, the
MCT-211 will send a low battery report to the receiver.
Compliance with Standards: EN 50131-1 Grade 2 Class II, EN50134
Operating Temperature: 0° to 50°C (32° to 122°F).
Dimensions: Ø 35 mm (1.4 in.).
Weight: 25 g (0.9 oz).
Color: Black (Purple button)
This device complies with Part 15 of the FCC Rules and RSS-210 of
Industry and Science Canada. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including
interference that may cause undesired operation.
WARNING: Changes or modifications to this unit not expressly
approved by the party responsible for compliance could void the user's
authority to operate the equipment.
This device complies with the essential requirements and provisions of
Directive 1999/5/EC of the European Parliament and of the Council of 9
March 1999 on radio and telecommunications terminal equipment.
The technical documentation as required by the European Conformity Assessment
procedure is kept at:
UNIT 6 MADINGLEY COURT CHIPPENHAM DRIVE KINGSTON MILTON KEYNES
MK10 0BZ. Telephone number: 0870 7300800, Fax number: 0870 7300801
D-2451-EPS MCT-211 Installation Instructions
GB/US: TRANSMIT BUTTON
SP: PULSADOR DE TRANSMISSIÓN
PT: BOTÃO DE TRANSMISSÃO
3. WRIST BAND AND PENDANT
INSTALLATION
All MCT-211 units are supplied with a wrist band and a neck strap
that allow the device to be worn on the wrist like a regular watch, or
around the neck like a pendant.
To use the wrist band, perform the following instructions:
A. Open and remove the Velcro neck strap fastener.
B. Thread the Velcro wrist strap through the two loops on the
transmitter with the adhesive side facing downward (see Figures
2a and 2b).
C. Fasten the wrist band, place it around the wrist and adjust as
required (see Figure 2c).
To use the pendant, perform the following instructions:
A. Thread the Velcro neck strap through the two loops on the
transmitter with the adhesive side facing upward (see Figures 3a
and 3b).
B. Fasten the Velcro clasp as shown Figure 3c.
C. Place the pendant around the neck.
4. TESTING AND MAINTENANCE
4.1 Testing a New Unit
Since the MCT-211 is supplied with the battery already installed, the
unit is practically ready to be tested.
A. "Teach" the target receiver the ID code of the tested transmitter,
as instructed in the target receiver's installation manual.
B. Stand 3 m (10 ft) away from a target receiver and operate the
MCT-211 by depressing its transmit pushbutton. Verify that the
transmitter LED lights, indicating good battery condition.
Note: The LED will light for 2 seconds even if you press the
button for a shorter duration.
C. Observe that the receiver's LED lights, and make sure that the
receiver reacts as programmed.
D. Operate the transmitter from various locations within the area
covered by the target receiver to determine "dead" locations,
where transmission is blocked by walls and large objects, or
affected by structural materials.
Note: If dead/marginal zones are a problem, relocating the
receiver may improve the performance.
4.2 Battery Replacement
Caution! Risk of explosion if battery is replaced by an incorrect type.
Dispose of used batteries according to the manufacturer's instructions.
The original battery supplied with the transmitter can be used for 3
years (for single transmission per day). Battery replacement will
therefore be needed very rarely. To replace the battery, perform steps
4.3, 4.4 and 4.5.
4.3 Opening the Case
A. Put the transmitter face down.
B. Loosen and remove the 4 screws shown in Figure 4. Take care
not to lose the screws.
C. Turn the transmitter over. Hold the base between the fingers of
one hand, and pull the cover off.
D. Make sure that the rubber ring that serves as a seal is in place
around the rim of the base. If it comes loose, save it for later use
together with the screws.
Note: The strap pivots are seated in open grooves at the two
edges of the base. If you put the base on the table "on its back",
the pivots and the two sections of the strap will remain in place.
Upon removing the cover, the top side of the transmitter module is
viewed (Figure 5). The battery clip and battery will be out of sight - they
are both located on the bottom (hidden) side of the module.
GB/US: LED INDICATOR
SP: LED TRANSMISOR
PT: LED INDICADOR
Fig. 1 – MCT-211
1