EN
8. DAILY USE
Before using the machine it is advisable
to proceed as indicated in paragraph 6.1
regarding its state.
Solid waste must be removed from items
before being washed.
In case of encrustations, soak items before
introducing them.
When putting items in the rack supplied,
make sure to arrange them so that the
dirtiest part receives water from the lower
wash arms yet without retaining
inside them.
Each time the cycle ends,
open the door and wait a
few moments to allow the
load to dry and cool naturally.
Wear protective gloves before
touching the load; it may still be
very hot.
Run a couple of cycles without loading
before using the machine for the first
time, to clean the inside and ducts of any
impurities.
It is advisable to change the tank water
every 25 washes or twice a day.
In machines with electronic
display, it is possible to set the
number of cycles after which
programmed or forced draining
is to be carried out. Too high
temperatures can cause starch
residues to stick to items.
Be careful not to touch the
heating element inside the
tank upon tank draining and
removing the overflow pipe, as
it may still be very hot.
At the end of the self-cleaning
cycle, with the tank empty,
clean the filters with running
water and remove the residuals
of dirt with a non-metallic
brush.
50
Place the filters and any other utensils back
inside the tank and close the door.
9. CARE AND MAINTENANCE
Check the detergent and rinse aid in the
respective containers every day.
Do not clean the appliance with direct or
high-pressure jets of water.
Do not use corrosive products such as
sodium hypochlorite or acids.
If the feed water has a high content of
calcium and magnesium salts, it is advisable
water
to
carry
out
regular
descaling
appropriate products in the correct doses
and concentrations.
Rinse thoroughly and dry
the internal parts where the
descaling product was applied!
In the event of prolonged idle periods
(several weeks), it is advisable to run the
dishwasher with clean water for 3 cycles
before starting the wash.
Before proceeding, make sure the wash and
rinse pump rotate freely.
To do this, use a screwdriver in the special
slot on the motor shaft (ventilation side).
In the electronic version, when the set
number of cycles is reached, the display will
show the message "SERVICE WARNING" to
prompt contacting technical assistance.
10. TROUBLESHOOTING
PROBLEMS
The control panel/display
does not light up
The tank does not fill
with water
with
Water filling does not
stop when the level is
reached
Inadequate washing
results
Inadequate tank
temperature
Unsatisfactory rinsing
Rinse temperature
too low
POSSIBLE CAUSES AND CURES
A) Make sure the wall power switch is turned on and that the
fuses are not blown;
B) Make sure the plug is properly inserted in the socket.
A) Check the supply water and that the shutoff valve is
open.
B) Make sure the pressure switch is not out of calibration or
out of order.
C) Check proper operation of the solenoid filling valve and
internal filter.
D) Make sure the overflow is fitted in place.
A) Make sure the pressure switch is not out of calibration or
out of order.
B) Check proper operation of the solenoid valve.
C) Make sure the inside of the air trap is not dirty
A) Make sure the detergent used is the correct type and in the
right dose (as recommended by the manufacturer).
B) Make sure the impeller nozzles are not clogged.
C) Make sure the tank water temperature is at least 55°C.
D) Make sure the pump filter is not clogged by impurities.
E) The wash cycle is too short. Repeat the cycle.
A) Check that the thermostat is not out of calibration, faulty
or incorrectly set (electromechanical machines).
B) Check the temperature setting on the board
C) Check proper operation of the tank heating element.
A) Check the water supply pressure.
B) Make sure the nozzles are not clogged with limescale.
C) Check proper operation of the solenoid valve.
D) Check proper operation of the supplementary pump (if
present).
E) Make sure there is rinse aid in the tank
F) Check the rinse water temperature (80÷85°C)
A) Make sure the thermostat is not out of calibration, faulty
or incorrectly set.
B) Check the temperature setting on the board
C) Check if the safety thermostat has intervened and verify
related
causes.
D) Check proper operation of the heating element.
E) Make sure the coil of the contactor for the boiler heating
element is not disconnected.
EN
51