Assembly; Putting Into Operation - Brill 32 ED Instrucciones De Uso

6. Assembly

Checking all the Parts are
Included
The box contains the following
parts:
Complete lawnmower
.
Grass catcher
.
1 Upper section of the guide
.
handle
2 Lower section of the guide
.
handle
Fixing components
.
Operating instructions
.
Fitting the Guide Handle
Insert the lower guide bar into the
holders in the housing on both
sides so that the smooth side
points outwards. Then screw in
the bar with the knurled bolts
supplied (fig. 1, item 1). The bar

7. Putting Into Operation

Always carry out a visual inspec-
tion before using your lawn-
mower to ensure that cutting
tool, retaining bolts and entire
cutting unit are not worn or
damaged. Always replace worn
or damaged cutting tools with
new parts to ensure the lawn-
mower is properly balanced (see
Maintenance, Care and Storage).
Setting the Cutting Height
Figure 2
The cutting height is set centrally
with a rotating knob and the
height is infinitely variable.
The cutting height set can be
read off the display in 5 mm
graduations.
Warning! Only set the cut-
A
ting height with the motor
turned off. Only set the cutting
height to a depth where the blades
of the cutting mechanism do not
touch the ground if it is uneven.
with the switch is inserted from
outside into the channels pro-
vided for the purpose and
screwed to the lower bar with
the knurled bolts and nuts pro-
vided (fig. 1, item 2). Ensure that
the cable runs on the outside
along the bar and is not trapped.
Fasten the cable by pushing the
clamp on to the lower part of the
bar from outside (fig. 1, item 3).
Catch Basket Assembly
Place the left half of the catch
basket (1) on a solid surface
and the right half of the catch
basket (2) on top as shown in
Illustration 7 – 9; the hooks (3)
must be stuck in the provided
slots (4) until they click into
place. Make sure that the entire
edge fits snugly. When the
Attaching the Connection Cable
Figures 3 + 4
Initially push the coupler of the
connecting cable onto the start
switch connector and then sus-
pend the cable in the strain relief
in such a way that the cable is
slightly sagging in the direction
of the starter switch connector
(fig. 3). The cable strain-relief
prevents the electrical plug and
socket connection being discon-
nected accidentally. Always
unwind the spare cable com-
pletely from the cable reel and
lay it out in large, loose coils.
Insert the plug in the
socket provided for the purpose.
The cable must be routed in such
a way that during mowing it
always lies on the side which
has already been mowed.
The cable must not be squeezed
through doors or windows.
Only ever pull the cable out
catch basket halves have been
properly fit, place the four screws
into the screw holes provided (5)
and tighten the screws as far as
they will go.
Environmental protection,
disposal
(pursuant to RL 2002 / 96 EC)
The packaging material
is made of recyclable
materials. Dispose of
packaging materials in
accordance with regu-
lations. Electrical appliances are
not to be disposed of in the nor-
mal household waste, they must
be professionally disposed of.
Important for Germany:
electrical appliances are to be
disposed of through your local
disposal sites.
of the socket by the plug
or coupling housing.
Starting
Figure 3
Place the lawnmower on a flat
area of the lawn. The lawn
mower may not be raised when
switching on the mower. If neces-
sary – only place at an angle
in such a way that the cutting
mechanism points in the direc-
tion away from the user.
When the motor is running,
always keep your hands and
feet away from the inner housing
and grass ejector. The mains
connection socket must be fused
with a minimum of 16 A.
To start the mower, press the
start button with one hand, pull
the safety handle towards the
guide bar with the other hand.
GB
17