Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
FOR
INSTALLATION OF
58058 OR 30035
RAIL KITS
1.
Do not install mounting rails over plastic bed liners. Plastic bed liners must be cut out of the way to provide metal to metal contact.
Mounting rails may be installed on spray in liners.
2.
Use only bolts, nuts, and washers supplied to install this kit. All bolts & nuts are Grade 5 unless otherwise specified.
3.
DO NOT INSTALL THIS PRODUCT ON OR ATTEMPT TO TOW WITH A TRUCK WITH A BED THAT IS
LESS THAN 6' LONG.
4.
These instructions are guidelines only, actual installation is the responsibility of the installer and the owner. Always measure truck
and trailer before installing hitch to be sure that there is clearance at the cab and at the bumper to allow for turns.
5.
Remove the plastic inner fender liner.
6.
Remove the spare tire if this helps to give more room to install the product.
7.
On the driver's side frame rail, temporarily remove the forward hex nuts and ground wires attached to the vehicle frame.
8.
Place the rearward mounting rail in the bed of the vehicle. Center the rail from left to right on the floor of the truck bed and use your
tape measure to locate the proper distance from the rear of the rail to the rear edge of the truck box as illustrated on page 3.
9.
Use a center punch to mark the holes in the rail per the illustration. Move the rail out of the way and drill each position through the
bed with a 1/8" drill bit. Note: On the driver's side of the vehicle the gas tank is located below the bed of the vehicle. When
drilling holes through the bed be sure not to damage the fuel tank or any other components.
For Dual Exhaust, unbolt driver's side exhaust hanger from cross-member and remove. If no Dual Exhaust, go to next step.
10.
11.
To place the c-channel above the vehicle frame cross member as shown on page 1, temporarily remove the plastic clips that hold the
wiring harness to the top of the vehicle frame cross member. Disconnect electrical connectors from both end of this harness section
and move it out of the way. Also remove the rear differential breather tube from the vehicle frame cross member and shock mount.
Place c-channel approximately centered from left to right. Check that the 1/8" drilled holes align with the slots in the c-channel.
12.
Enlarge the 1/8" drilled holes to 9/16" with a drill. Paint bare metal as required.
13.
Fasten the c-channel to the vehicle frame cross member as shown in Figure 1 using 5/8" hardware. Bolt up through the vehicle frame
cross member.
14.
Reposition the rear mounting rail over the holes in the bed and fasten the mounting rail to the c-channel using the supplied ½" hex
bolts (as shown in figure 1). Use the supplied U-shaped spacer plates between the c-channel or mounting rails and the truck bed to
ensure metal to metal contact.
15.
For Dual Exhaust, reattach exhaust hanger that was removed in step 10.
16.
Place the unassembled 5
rail with the support arches/slider/goose by inserting the tabs into the mounting rail and pushing the mounting rail tight towards the
other mounting rail. Ensure that the mounting rail is centered on the bed of the vehicle. This will position the rail in the correct
location and ensure that the 5
mounting rails then both types should be used at the same time to align the forward mounting rail. This will ensure that one product
does not compromise the fit of the other.
17.
Use a center punch to mark the holes in the forward rail per the illustration on page 3. Move the rail out of the way and drill each
position with a 1/8" drill bit. Enlarge the 1/8" drilled holes to 9/16" and paint bare metal as required. Reposition the mounting rails
over the holes drilled in the bed.
18.
Install edge protector onto curve section of driver's side bracket, next to fuel fill hose. Install the front frame rail brackets as shown
in figure 1, use supplied U-shaped spacer plates. The brackets install ahead of the hat section that supports the bed. Use the ½" pull
wire to pull the carriage bolts and square hole plates into the frame.
19.
Starting with the hex bolts that fasten the rails to the frame brackets thru the bed, torque all the nuts. Torque the hex bolts positioned
in the center of the rails. Torque the fasteners that attach the frame brackets to the vehicle frame then all remaining fasteners.
20.
Re-install the ground wire removed in installation step 7. Re-install spare tire. Re-attach the wiring harness and the differential
breather tube that were removed in step 11. Reinstall plastic inner fender liner.
21.
Torque the 1/2" fasteners to 75 (ft-lb.) 102 (N*M) Torque the 5/8" fasteners to 150 (ft-lb.) 204 (N*M).
2014 Cequent Performance Products
©
Printed in Mexico
Installation Instructions
CUSTOM QUICK INSTALL
MOUNTING KIT
Dodge Ram 1500
(Does not fit 5-1/2' beds)
th
wheel support arches/slider/goose into the already installed mounting rail. Position the forward mounting
th
wheel will have a snug fit to the truck. Note: If more than one hitch product will be used with the
Sheet 2 of 6
50141N
Part Numbers:
50141
10-8-14
Rev. B
Publicidad
Tabla de contenido
