I - Door Reversibility - Eurocave Revelation Modo De Empleo

4/ INSTALLING YOUR WINE CABINET
Precautions
•
Do not place your cabinet in an area liable to flood.
•
Do not place your cabinet close to a source of heat or expose it to
direct sunlight
•
Prevent water from splashing on any parts of the rear of the machine.
•
Arrange the power lead so that it is accessible and does not come into
contact with any of the appliance's components.
•
Tilt the cabinet slightly backwards in order to adjust the front feet (by
screwing or unscrewing them) so that you can level your cabinet (spirit
level recommended).
•
For 1-temperature models only, place the humidity cartridge (located in
your cabinet's "accessories" bag) in the base of the cabinet, under the
grid, in the tray provided (see diagram below). When using for the first
time, immerse the entire cartridge in water for a few minutes to saturate
it then drain it thoroughly.
•
Install the stop (which is located in the accessories bag) at the back of
the cabinet (see diagram).
•
This allows a space of 7 cm to be maintained between the wall and the
rear of the cabinet. This spa
ce allows your cabinet's power consumption to be optimised.
•
Place the 2 caps in the 2 holes at the top of the cabinet.
•
Do not push the caps all the way in, in order to allow the rear stop to
be installed.
•
Slide the rear stop between the caps and the wall of the cabinet, then
push the 2 caps all the way in.
Installation
Place your cabinet in the desired
location.
It must:
•
be open to the outside and well
ventilated (not in an enclosed
cupboard, for example),
•
not be too damp (utility room,
laundry room, bathroom...),
•
have a flat, stable floor,
•
be supplied with power (standard outlet, 16 A, earthed with 30mA*
circuit breaker). (* not applicable to some countries).
•
Place your cabinet in the desired location.
•
Fit the charcoal filter (located in the "accessories" bag) by inserting it
into the breather hole located on the top left-hand side of the inside of
your cabinet (see diagram below).
8
GB
•
Take the lead and plug it into the connector, located at the back of the
cabinet, on the bottom left-hand side.
•
Wait 48hrs before plugging in your cabinet
Fig.1
•
When using your cabinet for the first time, the charcoal filter alarm will
display. Reset the filter meter to 365 (see chapter 6, § VI).
Fitting the handle
(Full Glass and Black Piano doors only)
Fig.1
•
Unscrew the three screws placed on the side of the door, using the Allen
wrench, which you will find in the handle's box.
Fig.2
View from above
Seal
Handle
Front
Door frame
Figure 1 Fig.3
Fig.2
Figure 2
• Fig.3
Position the handle on the specially designed groove on the door frame
(figure 2).
•
Insert the handle all the way into the groove using a forward movement
(figure 2).
•
Screw the three screws back on (figure 3).
•
Take care not to catch the seal when screwing.
Note: adjustment of the handle is possible thanks to the oblong holes.
Door security
In order to make your cabinet secure, all doors have a lock.
Installing two cabinets side by side
N.B.: If you are placing two cabinets side by side, ensure that you leave a
gap of at least 1 cm between each cabinet.
Replacement of the LEDs on the control panel must
only be carried out by a qualified electrician.
Bottles must be arranged so that they do not come into contact
with the back wall. If this happens, the condensation created on
the wall may trickle onto the shelves and damage the bottle
labels. In addition, contact with the cold wall may create a frost point,
which is harmful to your wine.
4/ INSTALLING YOUR WINE CABINET
I. Door reversibility
x3 x3
A B C
This allows you to change the direction in which the door opens. Follow
the instructions below (example for changing a right-hand door into a left-
hand door):
Figure 3
4
1
Unscrew the three screws using a "T25" Torx wrench.
2
Remove the upper hinge.
3
Carefully remove the caps using a thin blade.
4
Remove the cabinet door by opening it slightly, then lifting it upwards.
5
Unscrew the door pin.
6
Carefully remove the cap using a thin blade and assemble the pin in its
place. Reposition the cap on the opposite side
7
7
Unscrew the two screws and the door catch. Unscrew the two screws
on the opposite side and remove the two washers.
8
Mount the door catch on the desired opening side, using screws.
Replace the washers, then the screws, on the side opposite the door catch..
x3 x4
A
Upper hinge
B
Caps
C
Caps
D E F G H J
D
Torx screw
E
Hex screw
x2
F
Door catch
G
Lower hinge
1
2
3
9
Turn the door through 180°.
Warning: the door is very heavy.
precautions to ensure that you do not injure yourself or drop it.
10
Put the door back on its pin.
8
11
Put in place the upper hinge.
12
Screw the hinge so that the door is completely parallel to the cabinet.
Check that the door seal adheres well to the cabinet (by closing the door),
to ensure that it is completely air-tight.
13
Put in place the caps.
H
Door pin
J
Door pin cap
Take any necessary
13
12
11
9
GB