Electrical Connection - Ryobi RBS904 Manual De Utilización

EN
FR DE ES IT NL
■ if the power supply cord is damaged, it must be
replaced only by the manufacturer or by an authorised
service centre to avoid risk.
■ save these instructions. Refer to them frequently
and use them to instruct other users. If you loan
someone this tool, loan them these instructions also.
ElEctrical
ExtEnsion corDs
Use only 3-wire extension cords that have 3-prong
grounding plugs and 3-pole receptacles that accept the
product's plug. When using a power tool at a considerable
distance from the power source, use an extension cord
heavy enough to carry the current that the product will
draw. An undersized extension cord will cause a drop in
line voltage, resulting in a loss of power and causing the
motor to overheat.
Before using an extension cord, inspect it for loose or
exposed wires and cut or worn insulation.
warninG
Keep the extension cord clear of the working area.
Position the cord so that it will not get caught on lumber,
tools, or other obstructions while you are working with
a power tool. Failure to do so can result in serious
personal injury.
warninG
Check extension cords before each use. If damaged
replace immediately. Never use the product with a
damaged cord since touching the damaged area could
cause electrical shock resulting in serious injury.

ElEctrical connEction

This product is powered by a precision-built electric motor.
It should be connected to a power supply that is 230-240
V, ac only (normal household current), 50 Hz. Do not
operate this product on direct current (DC). A substantial
voltage drop will cause a loss of power and the motor will
overheat. If the product does not operate when plugged
into an outlet, double check the power supply.
spEED anD wirinG
The no-load speed of this product is approximately 11 m/s.
This speed is not constant and decreases under a load
or with lower voltage. For voltage, the wiring in a shop
is as important as the motor's input power rating. A line
intended only for lights cannot properly carry a power tool
motor. Wire that is heavy enough for a short distance will
be too light for a greater distance. A line that can support
PT DA SV FI NO RU
English
PL CS HU RO LV LT
one power tool may not be able to support two or three
products.
GrounDinG instructions
This product must be grounded. In the event of a
malfunction or breakdown, grounding provides a path
of least resistance for electric current to reduce the
risk of electric shock. This product is equipped with an
electric cord having an equipment-grounding conductor
and a grounding plug. The plug must be plugged into a
matching outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
Do not modify the plug provided. If it will not fit the outlet,
have the proper outlet installed by a qualified electrician.
Repair or replace a damaged or worn cord immediately.
rEsiDual risKs
Even when the product is used as prescribed, it is still
impossible to completely eliminate certain residual risk
factors. The following hazards may arise and the operator
should pay special attention to avoid the following:
■ kick-back of work pieces or parts of work pieces due to
improper adjustment or handling
■ damage to the respiratory system
notE: Wear respiratory protection masks containing
filters appropriate to the materials being worked.
Ensure adequate workplace ventilation. Do not eat,
drink or smoke in the work area.
■ damage to hearing if effective hearing protection is not
worn.
spEcifications
product specifications
Input voltage
Power
Motor type
No load speed
Blade width
Blade length
Frame to blade capacity
Cutting thickness capacity
Table size
Dust port
4
ET HR SL SK EL TR
230-240 V, 50 Hz.
350 W
Induction
11 m/sec
6.35 mm (1/4")
1572 mm (62")
230 mm (9")
80 mm (3-1/8")
305 mm x 305 mm
(12" x 12")
53 mm (2-1/8")
UK