Ryobi FPR210 Manual De Utilización página 7

GB
FR DE ES
INSTALLING / REPLACING THE PAINT ROLLER TO
THE ROLLER HEAD
See Figure 3.
„ Place roller caps in each end of the paint roller.
„ Align pins in the end of each roller cap to the slot inside
the roller head. Snap into place.
INSTALLING THE PAINT ROLLER, CUT-IN OR COR-
NER PADS TO THE PAINT TUBES
See Figure 4.
Connect the roller head to the handle before installing to
the paint tube.
To connect roller head to handle:
„ Insert the collar on the roller head into the hole in the
handle until they "click" together.
„ Place the connector on the end of the paint tube into
the quick-connect outlet on the handle. Push until it
"clicks" into place. Pull on the tube to be certain it is
properly secured.
To attach cut-in pad or corner pad:
„ Insert the collar on the cut-in or corner pad into the
hole in the handle until they "click" together.
„ Place the connector on the end of the paint tube into
the quick-connect outlet on the handle. Push until it
"clicks" into place. Pull on the tube to be certain it is
properly secured.
SPECIFICATIONS
Paint area per minute
Tube length
Rating Input
OPERATION
APPLICATIONS
You may use this product for the purposes listed below:
Painting interior walls
LOADING PAINT CAN ONTO THE MACHINE
See Figure 5.
Place unit on a tarp or other protected surface. The ma-
chine will accept most cylindrical paint cans up to 3.8 liters.
„ Remove lid from paint can. Do not discard lid.
„ Stir paint before using.
„ Carefully place the paint can and lid in the paint con-
tainer well.
„ Place plastic paint container lid (included) onto the
paint can.
IT NL PT DK SE
Roller
3.6 m
230 V 50 Hz, 60 W
FI NO RU PL CZ
English
„ Lower the handle onto the paint can, aligning inlet
tubes on the handle with openings in the paint con-
tainer lid (included). Press down until inlet tubes snap
into openings securely.
„ Secure the handle by latching it into place.
IDEAL VISCOSITY
Water based paints and
emulsions
Oil based paints
Wood stains/Wood preser-
vatives
This sprayer can be used with solutions that take between
12 - 18 seconds to empty through the viscosity cup. Dip
the viscosity cup into the paint and À ll up. Time how long it
takes for the viscosity cup to empty. See Figure 14.
Using the chart (or instructions of manufacturer) as a
guide, determine if the material requires further thinning, if
so then thin accordingly.
If the paint requires thinning, start with a 10% dilution of
the paint. For example:
Amount of spray
material (ml)
Paint thinner (ml)
To do this, À ll a 1 liter container with the required paint.
Then use the viscosity cup supplied to add 100 ml of re-
quired thinner. Stir the contents thoroughly, measure the
2
2.2 m
viscosity using the viscosity chart above. If paint requires
further thinning then repeat the above step.
NOTE: Some paints are outside the ranges listed above.
Please contact our helpline for further information.
FORWARD/OFF/REVERSE SWITCH
See Figure 6.
The forward/off/reverse switch has three functions:
1. To paint, set the switch in the forward position. In for-
ward, the machine pulls the paint from the paint can
and into the paint roller, cut-in pad, or corner pad.
2. With the switch set on reverse, the machine pulls the
paint back through the paint tubes and into the paint
can/paint container leaving less paint to clean up.
3. To stop the Á ow of paint, set the switch in the off
position.
DUAL CONTROL LEVER
See Figure 7.
Do not adjust the dual control lever with the machine
turned on. Always turn the machine off before changing
2
HU RO LV LT EE
12 - 18 seconds
12 - 18 seconds
no dilution
1000 2000
100 200
HR SI SK GR TR
3000 4000
300 400