GRAPHITE 59G021 Instrucciones De Uso página 11

Name Half-round HCS wheel for wood
Type of
Wood, wood-based materials, plastics
material
Dividing and plunge cutting in corners and
Intended use
hardly accessible places, near surface
Narrow plunge cuts in solid wood, e.g. for air
Example
grates
HCS blade for wood
Name
Wood, wood-based materials, plastics
Type of
material
Dividing and plunge cutting in corners and
Intended use hardly accessible places, near surface
Cut outs in furniture boards, cutting cove bases
Example short, plunge cutting for fitting floor panels
Name Half-round wheel with tungsten coat
Type of Cement joints, soft ceramic tiles, hard plastics
material and other materials
Cutting short and cutting off close to edges,
Intended use
in
corners and hardly accessible places
Removal of joint, cutting holes in ceramic
Example
tiles and plastics
Delta sanding pad
Name
Wood, wood-based materials, abrasive
Type of
materials
material
Sanding in hardly accessible places and in
Intended use
corners
on a hard ground
Removal of mortar and glue for ceramic tiles,
Example
sanding solid wood, polishing
Stiff scraper
Name
Linings, floors, ceramic tiles
Type of
material
Scraping soft materials on a hard ground
Intended use
Removal of mortar residues, glue for lining or
Example
ceramic tiles
INSTALLATION AND REPLACEMENT OF SANDING PAPER
Sanding pad is equipped with hook-and-loop attachment system
for quick and easy replacement of sanding paper. Choose sanding
paper with appropriate gradation depending on the processed
material and desired level of material removal. All types of sanding
paper, abrasive cloths and polishing felt are allowed.
• Put the sanding paper close to the sanding pad (1).
• Press the sanding paper against the sanding pad (1).
• To remove sanding paper, lift edge of it on one side and pull
(fig. A).
INSTALLATION OF WORKING TOOLS
• Pull out the lever for quick-fastening of accessories (3) (fig. D).
• Insert your working tool between both washers of the tool chuck,
so that both openings match pins of the upper washer.
• To ensure operation in the most convenient and safe position for
the user, working tools can be placed in the tool chuck in any
position provided that they match pins of the upper washer (fig.
B).
• Your working tool should be inserted in such a manner, so that it
points downward with its bent section.
• Fasten the working tool in your selected position and lower the
lever for quick-fastening of accessories (3).
Check that the tool is installed properly. Improperly or
inaccurately installed working tools can slip during operation
and cause risk for the user.
DUST EXTRACTION
WARNING! Dust of some materials may be hazardous to
health, like paint coatings with lead additives, some types of
wood e.g. oak or beech or materials with asbestos. Therefore,
we recommend use of external dust extraction systems, good
workplace ventilation and use of dust-mask with particle filter.
OPERATION / SETTINGS
SWITCHING ON / SWITCHING OFF
The mains voltage must match the voltage on the label of the
tool.
Switching on – slide the switch (2) forward to position I (fig. C).
Switching off – slide the switch (2) backward to position O.
WARNING! Do not cover holes for motor ventilation in the
tool body.
SPEED ADJUSTMENT
The rotational speed of the motor is adjusted by turning and setting
the oscillation speed adjustment dial (4) in a required position. This
allows adjustment of working speed according to properties of your
workpiece. The oscillation speed adjustment ranges from 1 to 6.
The higher the value indicated by the oscillation speed adjustment
dial (4), the higher the working speed of the device is (fig. E).
PRINCIPLES OF OPERATION
Oscillation frequency 15000-21000 rpm at 2.8° angle allows to work
precisely in small areas and corners with the power tool.
SAWING AND CUTTING
Use only undamaged working tools in good technical condition.
When sawing or cutting wood, fibre board, wood-based
materials etc. make sure they do not contain foreign objects like
nails, bolts etc before starting the task. Remove foreign objects
or use proper blade for removal. You can make plunge cuts only
in soft materials like wood, gypsum boards and alike.
Cutting ceramic tiles causes faster wear of working tool.
SANDING
Working efficiency in surface sanding depends mainly on type and
quality of sanding paper and pressure applied for processing.
Overpressure does not make sanding more efficient, it only causes
10