Scope Of Supply - Wilo TWI 5 Instrucciones De Instalación Y Funcionamiento

English
domestic use (potable water supply)
agricultural use (watering, irrigation),
• Pumped liquids: non polluted, potable, cold, rain
waters.
The pump is not suitable for continuous use, e.g.
for the operation of fountains.
(Continuous operation > 2 hrs reduces the life-
time of the pump).
The pump must not be used for emptying swim-
ming pools.
5. Product
5.1 Type key
Pump family
SE - Lateral suction
nominal lowrate in m3/h
Number of stages
EM - Single phase 230V
DM - Tree phase 400V
B - Indice of technical evolution
5.2 Technicals characteristics
• Maximum operating pressure:
• Liquid temperatures max.:
• Power P1:
• Current:
• Speed of rotation:
• Protection index motor:
• Protection index switchbox (single phase): IP54
• Insulation class:
• Frequencie:
• Voltage
• Cable length:
• Max. starts per hour:
• Maximum immersion depth.:
• Maximum grain size.:
• Maximum sand content:
Outline and pipe connections: (See Fig. 1)

5.3 Scope of Supply

• Single phase pump with connecting cable
(H07RN-F) and switchbox with 2 m mains cable
and shock-proof plug,
or three phase pump with connecting cable
(H07RN-F) and a three cable end.
• Carrying rope 20m.
• Installation and operating instructions.
• Security instructions.
5.4 Accessories
Accessories must be ordered separately.
• Insulation valve
• Non return valve
• Command box and protection
• Circuit breaker
• Float switch
16
TWI5 - SE - 3 04 - DM / B
see rating platee
40 °C
see rating plate
see rating plate
see rating plate
IP68
F
50 Hz
Single phase: 230V (± 10 %)
Tree phase: 400V (± 10 %)
20m
40
20m
2mm
50g/m3
• Overflow sound alarm
• Fluid control
• Pressure switch
• Floating tapping device:
- suction coarse strainer,
- suction fine strainer
For specifications and descriptions of acces-
sories, see catalogue/data sheet.
5.5 Product description (Fig. 2, 3, 4, 5, 6 and 7)
1. Non return valve
2. Valve
3. Float switch
4. Connection box (single-phase)
5. Carrying rope
6. Fluid control
7. Supply cable
8. Float in low position
9. Float in high position
10. Pressure switch
11. Connection box (three phase)
12. Floating tapping device
13. Draining air hole to realize
14. Suction strainer
5.6 Design of pump and motor
The submersible pump is of the multi-stage,
centrifugal design.
All parts in contact with the flow medium are of
either corrosion-resistant material.
The electric motor is protected of the hydraulic
part pump by two mechanicals seal and a oil
chamber for maintained the tightness of the
motor.
The pumps are supplied with a carrying rope.
The pump base contains a suction strainer.
The SE type model are fitted with a suction sup-
port to allow the connection of floating or fixed
suction filters, together with a stand including 4
vibration absorbers for installation on the ground.
The single-phase motor pumps (EM) are deliv-
ered ready for connection with a switchbox. It
contains:
• Cut-out switch with indicator light,
• Built-in over current trip device in manual reset,
• Motor capacitor,
• Connection for a float switch (Low-water - / Dry
running protection),
• Cable connected to the terminal box as well as to
the pump,
• Connected 1 m long mains cable with shock-
proof plug.
The motor is fitted with a winding protection
which automatically switches the motor off if it
overheats and on again once it has cooled down.
Three-phase pumps (DM) are supplied with bare
cable lead ends.
The switch box can be ordered from the Wilo
range or provided by the customer.
It must be fitted with a motor safety switch.
Once the over current protective device has been
triggered the fault must be reset by operating
the cut-out switch.
WILO AG 10/2006