Manufacturer's Warranty - BTI PROFLINE RP 108 AR Manual De Instrucciones

eng
Keep the pressing tongs, pressing heads and expanding heads, and particularly
their receptacles, clean. Clean heavily soiled metal parts with turpentine oil, for
example, and then rustproof them.
Clean plastic parts (for ex. housing, batteries) only with a mild soap and a damp
cloth. Do not use domestic cleaning agents. These frequently contain chemicals
that can attack plastic parts. On no account use petrol, turpentine oil, thinners
or similar products to clean plastic parts.
Ensure that liquids never get inside the electrical equipment. Never immerse
the electrical equipment in liquid.
4.1.1. Pressing tongs
Check the pressing tongs for easy action at regular intervals. If necessary clean
the pressing tongs and lubricate the bolts (12) of the pressing jaws with machine
oil, however do not dismantle the pressing jaw! Remove any deposits in the
pressing contour (11). Check that all pressing tongs are func tional at regular
intervals by a trial pressing operation with the press fitting inserted. The pressing
jaws (10) must close (10) both at their tips (Fig. 1, at "A") and at the level of
the connecting link (Fig. 1, at "B") after completion of pressing. Do not use
damaged or worn pressing tongs again. If in doubt, return the drive unit together
with all pressing tongs to an authorised BTI after-sales service facility for
inspection.
4.1.2. Radial presses
Keep the press tongs receptacle clean, in particular clean the press rollers (5)
and tongs shank (2) at regular intervals and then lubricate them with machine
oil. Check the functional reliability of the drive unit regularly by making a pressing
with the largest press fitting used. If the pressing tongs close completely during
this pressing operation (see above), the drive unit is functionally reliable.
4.2. Inspection/repair
WARNING
Before any repair work, pull the mains plug or remove the battery! This
work may only be performed by qualified personnel.
The motor of the BTI RP 108 AR has carbon brushes. These are subject to
wear and must therefore be inspected or replaced from time to time. Only use
genuine BTI carbon brushes. The BTI Akku drive units operate electrohydrau-
lically. If the pressing power is insufficient or oil is lost, the drive unit must be
inspected and if necessary repaired by BTI or by an authorised BTI after-sales
service facility.
NOTICE
Damaged or worn pressing tongs cannot be repaired.
5. Trouble
For preventing damages make sure to avoid operating situations like exempla-
rily shown in Fig. 3 through 5, that no distortion between pressing tongs, fitting
and drive unit occurs.
5.1. Trouble: Drive unit does not operate.
Cause: ● Worn carbon brushes (BTI RP 108 AR).
● Mains lead defective (BTI RP 108 AR).
● Battery empty or defective (BTI Akku drive units).
● Drive unit defective.
5.2. Trouble: Radial press does not finish pressing operation, pressing tongs
do not close completely.
Cause: ● Drive unit overheated (BTI RP 108 AR).
● Worn carbon brushes (BTI RP 108 AR).
● Battery empty or defective (BTI Akku drive units).
● Drive unit defective.
● Incorrect pressing tongs (pressing contour, size) inserted.
● Pressing tongs with stiff action or defective.
5.3. Trouble: During closing of the pressing tongs, a marked ridge is created
on the compression sleeve.
Cause: ● Damaged or worn pressing tongs/pressing contour.
● Incorrect pressing tongs (pressing contour, size) inserted.
● Unsuitable matching of compression sleeve, pipe and support
sleeve.
5.4. Trouble: Pressing jaws close unevenly when the pressing tongs are not
loaded at "A" and "B" (Fig. 1).
Cause: ● Pressing tongs have been dropped, compression spring is bent.
6. Disposal
The drive units may not be thrown into the domestic waste at the end of use.
They must be disposed of properly by law.

7. Manufacturer's Warranty

The warranty period shall be 12 months from delivery of the new product to the
first user. The date of delivery shall be documented by the submission of the
original purchase documents, which must include the date of purchase and the
designation of the product. All functional defects occurring within the warranty
period, which are clearly the consequence of defects in production or materials,
will be remedied free of charge. The remedy of defects shall not extend or
renew the warranty period for the product. Damage attributable to natural wear
and tear, incorrect treatment or misuse, failure to observe the operational
instructions, unsuitable operating materials, excessive demand, use for unau-
thorized purposes, interventions by the customer or a third party or other
reasons, for which BTI is not responsible, shall be excluded from the warranty.
Services under the warranty may only be provided by customer service stations
authorized for this purpose by BTI. Complaints will only be accepted if the
product is returned to a customer service station authorized by BTI without
prior interference in an unassembled condition. Replaced products and parts
shall become the property of BTI.
The user shall be responsible for the cost of shipping and returning the product.
The legal rights of the user, in particular the right to make claims against the
seller under the warranty terms, shall not be affected. This manufacturer's
warranty only applies for new products which are purchased in the European
Union, in Norway or in Switzerland.
This warranty is subject to German law with the exclusion of the United Nations
Convention on Contracts for the International Sales of Goods (CISG).
eng