Stanley Fatmax FMCS701 Manual De Instrucciones página 13

Features
This tool includes some or all of the following features.
1. Trigger switch
2. Operating handle
3. Mounting holes
4. Lower Guard
5. Mitre locking knob
6. Mitre latch button
7. Kerf plate
8. Mitre scale
9. Mitre scale indicator
10. Carry grips
11. Fence
12. Bevel lock knob
13. Rails
13a.Velcro strap
14. Dust port
15. Battery pack
16. Work light switch
17. Lock off lever
18. Rail lock screw
19. Clamp mounting hole
20. Lock down pin
Assembly (Fig. A)
Your mitre saw is part assembled in the carton.
Open the box and lift the saw out by using the carry grips
u
(10) in the base of the saw (Fig. A).
Place the saw on a smooth, flat surface such as a work-
u
bench or strong table.
Examine Assembly diagram on page 2 of this manual to
u
become familiar with the saw and its various parts. The
section on adjustments will refer to these terms and you
must know what and where the parts are.
The mitre locking knob (5) is not assembled for shipping.
u
Remove the mitre locking knob (5) from the packaging
and screw onto the saw, see figure G and J for position.
Your saw has a built-in dust port (14) that allows either
u
the supplied, but not assembled, dust bag (35) or shop
vacuum system to be connected (Fig. N).
Kerf plate (Fig. J)
The kerf plate (7) is mounted to the table by 6 screws. The
kerf plate (7) height is not adjustable.
Note: If the kerf plate (7) is worn, damaged or needs to be
replaced, repairs should be carried out by authorised repair
agents or Stanley Fat Max service staff.
Lock down pin (Fig. F)
Warning! The lock down pin should be used ONLY when
carrying or storing the saw. NEVER use the lock down pin for
any cutting operation.
(Original instructions)
Note: To lift, carry and support the mitre saw during transport
use the two carrying handles (10) located on both sides of the
mitre saw base (Fig. A).
To lock the saw head in the down position, push the saw head
down, push the lock down pin (20) in and release the saw
head. This will hold the saw head safely down for transporting
the saw from place to place. To release, press the saw head
down and pull the pin out.
Warning! Always be sure that the tool is switched off and the
battery is removed from the tool before adjusting or checking
the tools function.
Charging a battery (fig. B)
Stanley FatMax chargers are designed to charge Stanley
FatMax battery packs.
Plug the charger (21) into an appropriate outlet before
u
inserting a battery pack (15).
Insert the battery pack (15) into the charger, making sure
u
the battery pack is fully seated in the battery slots
(Figure B).
The LED (21a) will flash indicating that the
battery is being charged.
The completion of charge is indicated by the
LED remaining on continuously. The pack is
fully charged and may be used at this time or
left in the charger.
Recharge discharged batteries as soon as possible after
u
use or battery life may be greatly diminished.
For longest battery life, do not discharge batteries fully.
u
It is recommended that the batteries be recharged after
each use.
Charger diagnostics (fig. C)
This charger is designed to detect certain problems that can
arise with the battery packs or the power source. Problems
are indicated by one LED flashing in different patterns.
Bad battery
The charger can detect a weak or damaged
battery. The LED flashes in the pattern indi-
cated on the label. If you see this bad battery
blink pattern, do not continue to charge the battery. Return it
to a service centre or a collection site for recycling.
Hot/cold pack delay
When the charger detects a battery that
is excessively hot or excessively cold, it
automatically starts a Hot/Cold Pack Delay,
suspending charging until the battery has normalized. After
this happens, the charger automatically switches to the Pack
ENGLISH
13