Hoonved HD 40 BT Instrucciones Para El Uso Y El Mantenimiento página 36

Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

ENGLISH
2.1
WASHING PHASES HD/LB
2.1.a Switching on and Preparing the machine (Fig.1)
To switch on the machine,press and hold the power
switch (Q1) into the ON position button for a few secon-
ds, then release.
The LED indicating the last cycle selected will become
CONSTANTLY LIT
(LC1, LC2, LC3 or LC1+LC2+LC3)
as will the
CHECK
LED .
IMPORTANT
On first switching on, LED
The boiler, and then the tank, will start to fill automatically.
Once the water level has been reached, the heating ele-
ments will switch in, first in the boiler, then in the tank.
Once the water in the tank reaches the correct tempera-
ture, the tank temperature LED (LTV) will go ON.
The thermometers
P3
(55°C) and
and boiler values of temperature.
WASHING OPERATION
If not equipped with an automatic dosing system, pour
into the tank a quantity of detergent suitable for the volu
me and hardness of the water. For quantities, refer to the
specific instructions for the detergent in use.
ATTENTION
When items to be washed are encrusted with burnt
on matter, or a long time has passed between use
and washing, it is essential to carry out a pre-was
soak using a suitable softening agent.
The use of hand-washing products is to be avoided
as they could produce foam inside the machine.
IPlace the basket of items to be washed inside the machine,
having first removed any solid waste.
2.1.b Selecting a Cycle
The duration of the washing cycle can be chosen from
4 different lengths of time, to be selected using the
"CYCLE" button.
Each time the "CYCLE" button is pressed, the LEDs
2.1.c STARTING UP THE WASHING CYCLE
The selection of MANUAL orAUTOMATIC start to be
made with machine in stand-by mode
Before to start the washing to make sure that the tempe
ratures are those cited, 55°C for the washing and 85°C
P3
P2
for I rinse
and
.
STARTING the MANUAL WASHING CYCLE
To start the washing cycle, press and hold the
(S3) button for a few seconds, then release.
Throughout the washing cycle the LED(s) for the selected
(LC1, LC2
LC3 or LC1+LC2+LC3)
cycle
or
36
LC2
will light up.
P2
(85°C) reflect the tank
IMPORTANT
START
will FLASH.
Part 2: For the operator
,
ATTENTION
We recommend that you top up the detergent used up
by washing grease or dispersed during rinsing every
4-5 complete cycles.
The use of the machine ensures rinsing at the ideal
temperature for hygienic purposes every time;
Indeed, if the temperature is not sufficient the wash will
be automatically prolonged so as to ensure the neces-
sary conditions of optimum rinsing at 85°C.
The waiting time required to attain optimum temperatu-
re can extend to a maximum of 8 minutes.
While this is taking place, the
RAPIDLY until the end of the cycle. To reset the
flashing, switch the machine off and back on using the
power switch (Q1) .
STARTINGUPTHEWASH. CYCLEAUTOMATICALLY
To start up the cycle AUTOMATICALLY (by opening and
closing the door), you will need to change the cycle
start up mode. Press and hold the "CYCLE" button until
the pre-selected cycle LED remains BLINKING LIT
(approx. 10 sec.) and the washing cycle will then start
up AUTOMATICALLY when the door is closed.
The functioning of the led (CONTINUOUS or BLINKING)
depends on the chosen type of functioning(MAN. or AUT)
2.1.d Interrupting the cycle
1) It is possible to interrupt the washing cycle momen-
tarily by opening the door, this is an EMERGENCY
measure:
the cycle LEDs
(LC1, LC2,LC3 or or LC1+LC2+LC3)
will start to FLASH, alternating with the
On closing the door, operations will resume from the
point in which they stopped.
2) The cycle can also be interrupted by SWITCHING
the machine's power switch (Q1) to the OFF position.
3) On switching the machine back on, the LED indica-
ting the last cycle selected will light up.
At the end of the washing cycle, take out the basket and
shake it gently so as to remove the last drops left on the
washed items.
Allow items to dry and remove them from the basket
with clean hands.
Store all items on hygienic and completely stable surfa-
ces.
2.1.e Manual Draining
It is possible to drain the water from the tank at any time
during the day, according to the waste accumulated.
To carry out this operation, proceed as follows:
- SWITCH the machine's power switch (Q1) to the OFF
position and release the overflow, allowing all the water
to drain from the tank;
- Remove the tank filters (19) and clean;
CHECK
LED will FLASH
CHECK
LED .

Publicidad

Tabla de contenido
loading

Tabla de contenido